As aero gas turbines strive for higher efficiencies and reduced fuel burn, the trend is for engine overall pressure ratio to increase. This means that engine cycle temperatures will increase and that cooling of various engine components, for example the high pressure turbine, is becoming more difficult. One solution is to employ a cooled cooling air system where some of the compressor efflux is diverted for additional cooling in a heat exchanger fed by air sourced from the by-pass duct. Design of the ducting to feed the heat exchangers with coolant air is challenging as it must route the air through the scenery present in the existing engine architecture which leads to a convoluted and highly curved system. Numerical predictions using ANSYS Fluent demonstrated that a baseline design was unsuitable due to large amounts of flow separation in the proximity of the heat exchangers. This paper is mainly concerned with the aerodynamic design of this component of the duct. In order to produce a viable aerodynamic solution a numerical design methodology was developed which significantly enhances and accelerates the design cycle. This used a Design of Experiments approach linked to an interactive design tool which parametrically controlled the duct geometry. Following an iterative process, individually optimized 2D designs were numerically assessed using ANSYS Fluent. These designs were then fed into an interactive 3D model in order to generate a final aerodynamic definition of the ducting. Further CFD predictions were then carried out to confirm the suitability of the design. RANS CFD solutions, generated, using a Reynolds stress turbulence model, suggested that the new design presented significant improvement in terms of diffusion and flow uniformity.

This paper uses Computational Fluid Dynamics to investigate the effect of an engine handling bleed situated on the outer casing downstream of the last rotor stage of a low-pressure compressor and upstream of the outlet guide vane and S-shaped duct. The model, validated against existing experimental data, utilized an unsteady RANS solver incorporating a Reynolds stress closure to examine the unsteady component interactions. The results showed that at bleed rates less than 25% of the mainstream flow the bleed effects were negligible. However, at higher bleed rates performance was significantly degraded. A uniform flow extraction hypothesis was employed to separate the positional bias effects from the bulk flow diffusion. This revealed that the bleed-induced radial flow distortion can significantly affect the OGV loading distribution, which thereby dictates the position and type of stall within the OGV passage. Extraction of the rotor tip leakage via the shroud bleed, combined with the radial flow distortion, contributed to a 28% reduction in duct loss at 10% bleed and up to 50% reduced loss at 25% bleed. The actual amount of flow required to be extracted for an OGV stall to develop, was 30%. That was independent of the bleed location and the type of stall. For bleeds up to 20%, the S-duct displayed a remarkable resilience and consistency of flow variables at duct exit. However, a stalled OGV deteriorated the radial flow uniformity that was presented to the high-pressure compressor.

Fluid off-takes and complex delivery ducts are common in many engineering systems but designing them can be a challenging task. At the conceptual design phase many system parameters are open to consideration and preliminary design studies are necessary to instruct the conceptualisation process in an iterative development of design ideas. This paper presents a simple methodology to parametrically design, explore and optimise such systems at low cost. The method is then applied to an aerodynamic system including an off-take followed by a complex delivery duct. A selection of nine input variables is explored via a fractional factorial design approach that consists of three individual seven-level cubic factorial designs. Numerical predictions are characterised based on multiple aerodynamic objectives. A scaled representation of these objectives allows for a scalarisation technique to be employed in the form of a global criterion which indicates a set of trade-off geometries. This leads to the selection of a set of nominal designs and the determination of their robustness which will eventually instruct the next conceptual design iteration. The results are presented and discussed based on criterion space, design variable space and contours of several flow quantities on a selection of optimal geometries.

This study explores the feasibility of using an oscillating plate downstream of a cylindrical body to produce mechanical energy from a Von Kármán vortex street. The study aims to quantify the impact of the plate length, its separation from the cylinder, and a machine damping factor on the power coefficient and the blade’s displacement to identify the optimal configuration. This preliminary assessment assumes that the plate oscillation is small enough to avoid changes in the vortex dynamics. This assumption allows the construction of a surrogate model using CFD to evaluate the effect of plate length and separation from the cylinder on the fluctuating lift forces over the plate. Later, the surrogate model, combined with varying machine damping factors, facilitates the description of the device’s dynamics through the numerical integration of an angular momentum equation. The results showed that a plate with 0.52D length, 5.548D separation from the cylinder, and a damping factor of 0.013 achieved a power coefficient of 0.147 and a perpendicular displacement of 0.266D. These results demonstrate a substantial improvement in the performance of bladeless generators.

The pollution generated by the aircraft engines at the start of the take-off run is an important contributor to the local air quality in proximity to airports. The installation of an array of baffles in the runway strip behind the start of the runway, a configuration aiming to accelerate the lift-off of the exhaust plume, is numerically investigated. Validation tests are carried out in an effort to limit the computational cost. In this way, experimental data, including mean and RMS velocity profiles, as well as passive scalar concentrations, have been referenced. Additionally, a Dynamic Response Algebraic Model for Baffle Imitation (DRAMBI) has been devised. The numerical model is presented and tested. Experimental data obtained in the Atmospheric Boundary Layer Wind Tunnel (ABLWT) of Cranfield University, including drag force measurements and passive scalar concentrations, are used for the validation of the model. The predictions of DRAMBI are also compared to the results of conventional simulations including the baffle geometries. In this way, two-dimensional volume sections of mean and RMS contours of velocity and passive scalar, are presented and analysed. Finally, the axial momentum reduction required so that buoyancy becomes dominant and the plume naturally lifts-off, is investigated.