We present an experimental study on the drilling of metal targets with ultrashort laser pulses at high repetition rates (from 50 kHz up to 975 kHz) and high average powers (up to 68 Watts), using an ytterbium-doped fiber CPA system. The number of pulses to drill through steel and copper sheets with thicknesses up to 1 mm have been measured as a function of the repetition rate and the pulse energy. Two distinctive effects, influencing the drilling efficiency at high repetition rates, have been experimentally found and studied: particle shielding and heat accumulation. While the shielding of subsequent pulses due to the ejected particles leads to a reduced ablation efficiency, this effect is counteracted by heat accumulation. The experimental data are in good qualitative agreement with simulations of the heat accumulation effect and previous studies on the particle emission. However, for materials with a high thermal conductivity as copper, both effects are negligible for the investigated processing parameters. Therefore, the full power of the fiber CPA system can be exploited, which allows to trepan high-quality holes in 0.5mm-thick copper samples with breakthrough times as low as 75 ms.

We study the incubation effect during laser ablation of stainless steel with ultrashort pulses to boost the material removal efficiency at high repetition rates. The multi-shot ablation threshold fluence has been estimated for two pulse durations, 650-fs and 10-ps, in a range of repetition rates from 50 kHz to 1 MHz. Our results show that the threshold fluence decreases with the number of laser pulses N due to damage accumulation mechanisms, as expected. Moreover, approaching the MHz regime, the onset of heat accumulation enhances the incubation effect, which is in turn lower for shorter pulses at repetition rates below 600 kHz. A saturation of the threshold fluence value is shown to occur for a significantly high number of pulses, and well fitted by a modified incubation model.

The influence of pulse duration on the laser drilling of metals at repetition rates of up to 1 MHz and average powers of up to 70 W has been experimentally investigated using an ytterbium-doped-fiber chirped-pulse amplification system with pulses from 800 fs to 19 ps. At a few hundred kilohertz particle shielding causes an increase in the number of pulses for breakthrough, depending on the pulse energy and duration. At higher repetition rates, the heat accumulation effect overbalances particle shielding, but significant melt ejection affects the hole quality. Using femtosecond pulses, heat accumulation starts at higher repetition rates, and the ablation efficiency is higher compared with picosecond pulses.

Silver nanoparticles (AgNPs) are well-known for their antimicrobial effects and several groups are proposing them as active agents to fight antimicrobial resistance. A wide variety of methods is available for nanoparticle synthesis, affording a broad spectrum of chemical and physical properties. In this work, we report on AgNPs produced by laser ablation synthesis in solution (LASiS), discussing the major features of this approach. Laser ablation synthesis is one of the best candidates, as compared to wet-chemical syntheses, for preparing Ag nano-antimicrobials. In fact, this method allows the preparation of stable Ag colloids in pure solvents without using either capping and stabilizing agents or reductants. LASiS produces AgNPs, which can be more suitable for medical and food-related applications where it is important to use non-toxic chemicals and materials for humans. In addition, laser ablation allows for achieving nanoparticles with different properties according to experimental laser parameters, thus influencing antibacterial mechanisms. However, the concentration obtained by laser-generated AgNP colloids is often low, and it is hard to implement them on an industrial scale. To obtain interesting concentrations for final applications, it is necessary to exploit high-energy lasers, which are quite expensive. In this review, we discuss the pros and cons of the use of laser ablation synthesis for the production of Ag antimicrobial colloids, taking into account applications in the food packaging field.

A new type of nanomaterial has been developed as antibacterial additive for food packaging applications. This nanocomposite is composed of copper nanoparticles embedded in polylactic acid, combining the antibacterial properties of copper nanoparticles with the biodegradability of the polymer matrix. Metal nanoparticles have been synthesised by means of laser ablation, a rising and easy route to prepare nanostructures without any capping agent in a liquid environment. As prepared, nanoparticle suspensions have been easily mixed to a polymer solution. The resulting hybrid solutions have been deposited by drop casting, thus obtaining self-standing antibacterial packages. All samples have been characterized by UV-Vis spectroscopy, X-ray photoelectron spectroscopy and electro-thermal atomic absorption spectroscopy. Ion release data have been matched with bioactivity tests performed by Japanese Industrial Standard (JIS) method (JIS Z 2801:2000) against Pseudomonas spp., a very common Gram-negative microbial group able to proliferate in processed food.