Fibre lasers are now associated with high average powers and very high beam qualities. Both these characteristics are required by many industrial, defence and scientific applications, which explains why fibre lasers have become one of the most popular laser technologies. However, this success, which is largely founded on the outstanding characteristics of fibres as an active medium, has only been achieved through researchers around the world striving to overcome many of the limitations imposed by the fibre architecture. This Review focuses on these limitations, both past and current, and the creative solutions that have been proposed for overcoming them. These solutions have enabled fibre lasers to generate the highest diffraction-limited average power achieved to date by solid-state lasers
We report on the observation and experimental characterization of a threshold-like onset of mode instabilities, i.e. an apparently random relative power content change of different transverse modes, occurring in originally single-mode high-power fiber amplifiers. Although the physical origin of this effect is not yet fully understood, we discuss possible explanations. Accordingly, several solutions are proposed in this paper to raise the threshold of this effect.
The temporal behavior of mode instabilities in active large mode area fibers is experimentally investigated in detail. Thus, apart from the onset threshold of mode instabilities, the output beam is characterized using both high-speed camera measurements with 20,000 frames per second and photodiode traces. Based on these measurements, an empiric definition of the power threshold of mode instabilities is introduced. Additionally, it is shown that the temporal dynamics show a transition zone between the stable and the unstable regimes where well-defined periodic temporal fluctuations on ms-timescale can be observed. Finally, it is experimentally shown that the larger the mode-field area, the slower the mode-instability fluctuation is. The observations support the thermal origin of mode instabilities.
Rare earth-doped fibres are a diode-pumped, solid-state laser architecture that is highly scalable in average power. The performance of pulsed fibre laser systems is restricted due to nonlinear effects. Hence, fibre designs that allow for very large mode areas at high average powers with diffraction-limited beam quality are of enormous interest. Ytterbium-doped, rod-type, large-pitch fibres (LPF) enable extreme fibre dimensions, i.e., effective single-mode fibres with mode sizes exceeding 100 times the wavelength of the guided radiation, by exploiting the novel concept of delocalisation of higher-order transverse modes. The non-resonant nature of the operating principle makes LPF suitable for high power extraction. This design allows for an unparalleled level of performance in pulsed fibre lasers.
We report on the experimental demonstration of a fiber chirped- pulse amplification system capable of generating nearly transform-limited sub 500 fs pulses with 2.2 mJ pulse energy at 11 W average power. The resulting record peak power of 3.8 GW could be achieved by combining active phase shaping with an efficient reduction of the acquired nonlinear phase. Therefore, we used an Ytterbium-doped large-pitch fiber with a mode field diameter of 105 µm as the main amplifier.
Mode instabilities, i.e. the rapid fluctuations of the output beam of an optical fiber that occur after a certain output power threshold is reached, have quickly become one of the most limiting effects for the further power scaling of fiber laser systems. Even though much work has been done over the last year, the exact origin of the temporal dynamics of this phenomenon is not fully understood yet. In this paper we show that the origin of mode instabilities can be explained by taking into account the interplay between the temporal evolution of the three-dimensional temperature profile inside of the active fiber and the related waveguide changes that it produces via the thermo-optical effect. In particular it is proposed that non-adiabatic waveguide changes play an important role in allowing energy transfer from the fundamental mode into the higher order mode. As it is discussed in the paper, this description of mode instabilities can explain many of the experimental observations reported to date.
In this paper we present a simple model to predict the behavior of the transversal mode instability threshold when different parameters of a fiber amplifier system are changed. The simulation model includes an estimation of the photodarkening losses which shows the strong influence that this effect has on the mode instability threshold and on its behavior. Comparison of the simulation results with experimental measurements reveal that the mode instability threshold in a fiber amplifier system is reached for a constant average heat load value in good approximation. Based on this model, the expected behavior of the mode instability threshold when changing the seed wavelength, the seed power and/or the fiber length will be presented and discussed. Additionally, guidelines for increasing the average power of fiber amplifier systems will be provided.
This work presents a review on the effect of transverse mode instability in high-power fiber laser systems and the corresponding investigations led worldwide over the past decade. This paper includes a description of the experimental observations and the physical origin of this effect, as well as some of the proposed mitigation strategies.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.