Study on the effects of raw materials composition and pelletization conditions on the quality and properties of pellets obtained from different woody and non woody biomasses.
The paper considers the issues of increasing the reliability of agricultural machinery through the use of reinforcing processing of recovered machine parts by plastic deformation, which provides an increase in the quality of their surface layer during recovery.
The operational stability of the piston fingers and the upper heads of the connecting rods restored by vibration reinforcement on the engines working in the mechanized agricultural complex was carried out: tractor - agricultural machine - car. Studies have shown that the amount of wear of piston fingers restored by the vibration deformation method is 1.23 times smaller than the traditional method of recovery, which confirms the effectiveness of vibration technology.
Technological processes of restoration of discs of diggers of beet harvesters, discs of coulters of grain planers, plow blades with use of vibrating vibrations of the processing tool are developed and put into production.
The results of these developments showed an increase of 1.21 times the time of beet harvester harvesting with the diggers' wheels with the vibration-strengthened method; an increase in technical use factor of 1.07 times, compared to new 65G steel wheels.
To improve the reliability of the PLN-5-35, PLN-3-35 plows, the technology of restoration of working bodies - blades is developed and introduced into production, which provides for increase of their durability and durability.
The coefficient of technical use of the plow units with the blades restored by the developed technology is 1.01 times higher than that of the plow units with the new blades made of 65G steel.
The wear rate of the toe, width and thickness of the blade are 1.51 respectively; 1.22 and 1.27 times less than the new 65G steel blades.
The results of the study of vibrating reinforcing processing of working bodies of agricultural machinery help to increase their resource, which provides increased reliability of machines.
The trees (e.g., fruit or decorative) growing on the homestead plots of private households provide opportunities for sustainable biomass obtained from pruned branches every year. Profitable production of fuel material requires high-performance equipment and methods by which wood chips can be produced at low cost. The practice of chopping tree branches shows that not all chopping machines are suitable for use on homestead plots. This research gives the five-year test results of a developed and patented tree branch chopping machine under special operating conditions. The machine was tested under the conditions of the homestead plot of a private household in the Poltava region, and the engineering parameters to set up the chopper were determined. It is recommended to set a 0.3404 radian (19 degrees 50 min) angle on the chopper to cut tree branches as well as to set the size of the cutting knives’ protrusion above the disc plane within 0.0120 m. As a result of the correct settings, the power consumption of the chopper motor will be W = 1.3549 kW, which is an optimal value for the studied chopper. The research results made it possible to provide instructions for the tree branch chopper’s operation and to adapt it to the conditions of homestead plots.
Метою роботи є дослідження технологічного процесу зміцнення пустотілих циліндричних деталей автотракторних двигунів з використанням поверхневого пластичного деформування. Попередньо проведені експериментальні дослідження на моделях у широкому діапазоні зміни різних факторів. Одержані дані перераховувались з моделі на конкретні деталі-поршневі пальці та втулки верхніх головок шатунів автотракторних двигунів. Дослідження використовували при визначенні: зусиль, напружень, формозміни, властивостей та структури матеріалу деталей. При проведенні досліджень дотримувався закон подібності, відповідно до якого моделі-зразки та деталі були геометрично подібними та фізично однакові. Експериментально встановлені раціональна форма обробного інструменту-конусна, а також його оптимальні розміри: кут нахилу 10°30′, величина калібруючого пояска 6-7 мм, що забезпечують величину зміцнення та якість поверхні оброблюваного матеріалу. Експериментально встановлено вплив кута нахилу обробного інструменту на величину налипання металу на його робочу поверхню. Встановлена залежність кількості налипання металу від його твердості та модуля пружності. Визначено вплив висоти калібруючої частини обробного інструменту на шорсткість оброблюваної поверхні деталі. На основі одержаних лабораторних даних отримана емпірична залежність припуску на обробку із залишковою деформацією по зовнішньому діаметру поршневого пальця. Виявлено, що найбільш небезпечними є тангенційні напруження по зовнішній поверхні поршневих пальців, визначення яких проводили в процесі деформування методом тензометрування. Експериментально встановлено значення припуску за один прохід робочого інструменту при вібраційному деформуванні поршневих пальців, що забезпечує зменшення розтягуючих залишкових напружень. Проведеними дослідженнями статичної міцності поршневих пальців встановлено, що величина зносу залежить від наступних основних факторів: методу обробки, матеріалу та часу роботи. Дослідженням вагового зносу поршневих пальців та втулок верхніх головок шатунів встановлено, що при вібраційному деформуванні величина зносу менша у порівнянні зі звичайною роздачею. Величина зносу поршневих пальців, що відновлені вібраційним методом, в 1,13 рази менше в порівнянні з відновленими звичайною роздачею Ключові слова: пластичне деформування, моделювання процесу, вібраційна обробка, залишкові напруження, шорсткість поверхні, зміцнення
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.