Self-compacting concrete (SCC) is a type of concrete that is placed in the formwork under its own weight. Although there are many studies showing the behavior of SCC beams, most relate to the behavior of simple supported beams. Unlike those, this is a study of continuous beams made of SCC aimed to analyze their flexural performance as well as to confirm the possibility of using nonlinear finite element analysis (FEA) in the design of such structural elements. An experimental study of three two-span continuous beams of a total length of 3400 mm, with the span between supports of 1600 mm, with 150/200 mm cross section made of SCC exposed to short-term loading, was carried out. The parameter that varied is the percentage of tensile reinforcement, with values of 0.65, 0.86 and 0.94 being selected. As all analyzed beams have shown a satisfactory load-bearing capacity and stiffness, the research confirmed the possibility of using SCC in continuous beams in civil engineering practice. Using Abaqus/Standard software, a nonlinear numerical model is proposed, which is validated and verified against experimental research, as there is only a 5% difference in the numerically calculated ultimate load compared to the experimentally measured values.
Strengthening of concrete structures is applied as a solution for various deterioration problems in civil engineering practice. This also refers to the structures made of self-compacting concrete (SCC), which is increasingly in use, but there is a lack of research in this field. This paper presents an experimental analysis of flexural behavior of reinforced concrete (RC) continuous beams made of SCC, strengthened with fiber reinforced polymer (FRP) materials (glass (GFRP) and carbon (CFRP) bars, CFRP laminates), by the use of near surface mounted (NSM) and externally bonded (EB) methods. Six two-span continuous beams of a total length of 3200 mm, with the span between supports of 1500 mm and 120/200 mm cross section, were subjected to short-term load and tested. The displacements of beams and the strains in concrete, steel reinforcement, FRP bars and tapes were recorded until failure under a monotonically increasing load. The ultimate load capacities of the strengthened beams were enhanced by 22% to 82% compared to the unstrengthened control beam. The ductility of beams strengthened with GFRP bars was satisfactory, while the ductility of beams strengthened with CFRP bars and tapes was very small, so the failure modes of these beams were brittle.
A solution for the elastoplastic deflection of cantilever beams with linearly variable circular cross-section loaded by shear force at the free end, which is suitable for practical use, has not yet been developed. A semi-analytical solution for such a problem is proposed in this paper. The solution involves beams made of homogenous and isotropic materials with bilinear elastoplastic strain hardening behavior. The Bernoulli–Euler formula is used for determining the elastic deflection. However, for the plastic domain of material behavior, the differential equation of beam bending does not have a solution in closed form. Therefore, an incremental procedure for determining the curvature of the plastified region of the beam is suggested. Deflection of the cantilever beam is calculated via integration of the approximated function of the beam curvature. The proposed semi-analytical solution is validated using experimental results of the seismic energy dissipation device components which have been selected as a sample of a real engineering system. Also, validation is done via finite element analysis of six different cantilever beam models with varying geometric and material characteristics. A satisfying agreement between the proposed semi-analytical results and the subsequent experimental and numerical results is herein achieved, confirming its reliability.
The topic of this paper is experimental and numerical analysis of the impact strength of unreinforced concrete slabs. Impact strength of concrete is significant in case of some accidental loads during exploitation. Impact strength can be determined experimentally, using Drop-weight test, Charpy test, Projectile impact test, Explosive test, etc. In this research, a numerical model for determining the impact strength of concrete slabs based on Finite element method (FEM) and high-end engineering software has been proposed. Modelling approach to this problem was applying the Explicit dynamics FEM analysis. Thereat, two different existing material models for concrete were enforced: Concrete damage plasticity model – CDP (implemented in ABAQUS/Explicit software), and the Riedel-Hiermaier-Thoma model – RHT (implemented in ANSYS Workbench software). Analysis parameters for both material models, necessary as input data, have been determined through a series of FEM analyses and validated by performed experiments, using drop-weight test. Results of the numerical analyses have been compared with the experimental ones, as well as mutually. Advantages and drawbacks of both material models are highlighted, as well as the reliability of the proposed numerical models. The proposed numerical FE models, confirmed by experiments, can be successfully used for determining impact strength of concrete slabs in further research.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.