This work reports on the fabrication, characterization and applications of Nafion-coated bismuth-film electrodes (NCBFE's) for the determination of trace metals by anodic stripping voltammetry (ASV). A NCBFE was typically prepared by first applying a 5 microl drop of a 1% Nafion solution onto the surface of a glassy-carbon rotating-disk electrode. After evaporation of the solvent, the Bi film was plated on the electrode in situ(i.e. by spiking the sample with 1000 microg l(-1) of Bi(iii) and simultaneous electrolytic deposition of the metal ions and bismuth film on the electrode surface at -1.4 V) or ex-situ(i.e. by electrolytic deposition of the bismuth film in a separate solution containing 1000 microg l(-1) of Bi(iii), followed by the ASV measurement step in the sample solution). Various fabrication and operational parameters were thoroughly investigated and discussed in terms of their effect on the ASV signals. It was found that this voltammetric sensor was suitable for the determination of metals at trace levels by square-wave ASV (SWASV) due to its multi-element detection potential, improved analytical sensitivity, high resistance to surfactants, low cost, ease of fabrication, robustness, speed of analysis and low toxicity (as compared to traditional mercury electrodes). In the presence of 4 mg l(-1) of Triton X-100, the NCBFE afforded a 10-fold peak height enhancement for the Pb peak and a 14-fold enhancement for the Cd peak over a bare BFE while the determination of Zn was feasible only on the NCBFE. The limits of detection (at a signal-to-noise ratio of 3) were 0.1 microg l(-1) for Cd and Pb and 0.4 microg l(-1) for Zn for a deposition time of 10 min. Finally, the electrode was applied to different real samples (tap-water, urine and wine) for the analysis of trace metals with satisfactory results.

No abstract

No abstract

Recent advances in adsorptive stripping voltammetry (AdSV) are reviewed. The mechanisms of the adsorptive and stripping steps are given. The criteria of ligand selection, along with the present status and future trends in AdSV for trace element analysis, are discussed. Tables containing the elements determined by AdSV and the ligands used in AdSV, as well as the real samples analyzed and operational conditions, are presented (together with 171 references).

No abstract

No abstract

This works reports the use of adsorptive stripping voltammetry (AdSV) for the trace determination of chromium on a rotating-disk bismuth-film electrode (BFE). During the reductive accumulation step, all the chromium species in the sample were reduced to Cr(III) which was complexed with cupferron and the complex was accumulated by adsorption on the surface of a preplated BFE. The stripping step was carried out by using a square-wave (SW) potential-time voltammetric signal. Electrochemical cleaning of the bismuth film was employed, enabling the same bismuth film to be used for a series of measurements in the presence of dissolved oxygen. The experimental variables as well as potential interferences were investigated and the figures of merit of the method were established. Using the selected conditions, the 3s limit of detection for chromium was 100 ng L À1 (for 120 s of preconcentration) and the relative standard deviation was 3.6% at the 2 mg L À1 level (n ¼ 8). Finally, the method was applied to the determination of chromium in real samples with satisfactory results.

Curcumin (CU) shows a wide range of pharmacological properties including antioxidant, anti-inflammatory, and antitumor effects. In order to understand the chemical basis of different activities of curcumin, we have studied the oxidation and reduction of curcumin. Based on cyclic and differential pulse voltammetric methods, using carbon paste and hanging mercury drop electrodes, in the present study we tested different parameters to optimize the conditions for the determination of curcumin and its electrochemical characteristics. Better results were obtained via differential pulse voltammetry using carbon paste electrode. Curcumin yields well-defined differential pulse voltammetric responses with well-defined oxidation (in the potential region of 0.3 -0.6 V, vs. Ag/AgCl) and reduction (at 0.3 V) peaks using carbon paste electrode.