We demonstrate high yield vapor-liquid-solid (VLS) growth of [100]-oriented InP nanowire arrays. The highest yield (97%) is obtained when the catalyst droplet is filled with indium prior to nanowire nucleation to the equilibrium composition during nanowire growth. Using these [100] wires as a template we can reversibly switch between a [100] and a [111] growth direction by varying the indium content of the droplet. Modeling VLS growth by a kinetic nucleation model indicates that the growth direction is governed by the liquid-vapor interface energy that is strongly affected by the indium concentration in the catalyst droplet.

We demonstrate an efficiency enhancement of an InP nanowire (NW) axial p-n junction solar cell by cleaning the NW surface. NW arrays were grown with in situ HCl etching on an InP substrate patterned by nanoimprint lithography, and the NWs surfaces were cleaned after growth by piranha etching. We find that the postgrowth piranha etching is critical for obtaining a good solar cell performance. With this procedure, a high diode rectification factor of 10(7) is obtained at ±1 V. The resulting NW solar cell exhibits an open-circuit voltage (Voc) of 0.73 V, a short-circuit current density (Jsc) of 21 mA/cm(2), and a fill factor (FF) of 0.73 at 1 sun. This yields a power conversion efficiency of up to 11.1% at 1 sun and 10.3% at 12 suns.

Semiconductor nanowire arrays are expected to be advantageous for photoelectrochemical energy conversion due to their reduced materials consumption. In addition, with the nanowire geometry the length scales for light absorption and carrier separation are decoupled, which should suppress bulk recombination. Here, we use vertically aligned p-type InP nanowire arrays, coated with noble-metal-free MoS3 nanoparticles, as the cathode for photoelectrochemical hydrogen production from water. We demonstrate a photocathode efficiency of 6.4% under Air Mass 1.5G illumination with only 3% of the surface area covered by nanowires.

III/V semiconductor nanostructures have significant potential in device applications, but effective surface passivation is critical due to their large surface-to-volume ratio. For InP such passivation has proven particularly difficult, with substantial depassivation generally observed following dielectric deposition on InP surfaces. We present a novel approach based on passivation with a phosphorus-rich interfacial oxide deposited using a low-temperature process, which is critical to avoid P-desorption. For this purpose we have chosen a POx layer deposited in a plasma-assisted atomic layer deposition (ALD) system at room temperature. Since POx is known to be hygroscopic and therefore unstable in atmosphere, we encapsulate this layer with a thin ALD Al2O3 capping layer to form a POx/Al2O3 stack. This passivation scheme is capable of improving the photoluminescence (PL) efficiency of our state-of-the-art wurtzite (WZ) InP nanowires by a factor of ∼20 at low excitation. If we apply the rate equation analysis advocated by some authors, we derive a PL internal quantum efficiency (IQE) of 75% for our passivated wires at high excitation. Our results indicate that it is more reliable to calculate the IQE as the ratio of the integrated PL intensity at room temperature to that at 10 K. By this means we derive an IQE of 27% for the passivated wires at high excitation (>10 kW cm–2), which constitutes an unprecedented level of performance for undoped InP nanowires. This conclusion is supported by time-resolved PL decay lifetimes, which are also shown to be significantly higher than previously reported for similar wires. The passivation scheme displays excellent long-term stability (>7 months) and is additionally shown to substantially improve the thermal stability of InP surfaces (>300 °C), significantly expanding the temperature window for device processing. Such effective surface passivation is a key enabling technology for InP nanowire devices such as nanolasers and solar cells.

Surface attachment of a planktonic bacteria, mediated by adhesins and extracellular polymeric substances (EPS), is a crucial step for biofilm formation. Some pathogens can modulate cell adhesiveness, impacting host colonization and virulence. A framework able to quantify cell-surface interaction forces and their dependence on chemical surface composition may unveil adhesiveness control mechanisms as new targets for intervention and disease control. Here we employed InP nanowire arrays to dissect factors involved in the early stage biofilm formation of the phytopathogen Xylella fastidiosa. Ex vivo experiments demonstrate single-cell adhesion forces up to 45 nN, depending on the cell orientation with respect to the surface. Larger adhesion forces occur at the cell poles; secreted EPS layers and filaments provide additional mechanical support. Significant adhesion force enhancements were observed for single cells anchoring a biofilm and particularly on XadA1 adhesin-coated surfaces, evidencing molecular mechanisms developed by bacterial pathogens to create a stronger holdfast to specific host tissues.

Nanophotonic engineering shows great potential for photovoltaics: the record conversion efficiencies of nanowire solar cells are increasing rapidly and the record open-circuit voltages are becoming comparable to the records for planar equivalents. Furthermore, it has been suggested that certain nanophotonic effects can reduce costs and increase efficiencies with respect to planar solar cells. These effects are particularly pronounced in single-nanowire devices, where two out of the three dimensions are subwavelength. Single-nanowire devices thus provide an ideal platform to study how nanophotonics affects photovoltaics. However, for these devices the standard definition of power conversion efficiency no longer applies, because the nanowire can absorb light from an area much larger than its own size. Additionally, the thermodynamic limit on the photovoltage is unknown a priori and may be very different from that of a planar solar cell. This complicates the characterization and optimization of these devices. Here, we analyse an InP single-nanowire solar cell using intrinsic metrics to place its performance on an absolute thermodynamic scale and pinpoint performance loss mechanisms. To determine these metrics we have developed an integrating sphere microscopy set-up that enables simultaneous and spatially resolved quantitative absorption, internal quantum efficiency (IQE) and photoluminescence quantum yield (PLQY) measurements. For our record single-nanowire solar cell, we measure a photocurrent collection efficiency of >90% and an open-circuit voltage of 850 mV, which is 73% of the thermodynamic limit (1.16 V).

The diameter dependence of the thermal conductivity of InAs nanowires in the range of 40-1500 nm has been measured. We demonstrate a reduction in thermal conductivity of 80% for 40 nm nanowires, opening the way for further design strategies for nanoscaled thermoelectric materials. Furthermore, we investigate the effect of thermal contact in the most common measurement method for nanoscale thermal conductivity. Our study allows for the determination of the thermal contact using existing measurement setups. The thermal contact resistance is found to be comparable to the wire thermal resistance for wires with a diameter of 90 nm and higher.

The functionality of semiconductor devices is determined by the incorporation of dopants at concentrations down to the parts per million (ppm) level and below. Optimization of intentional and unintentional impurity doping relies on methods to detect and map the level of impurities. Detecting such low concentrations of impurities in nanostructures is however challenging to date as on the one hand methods used for macroscopic samples cannot be applied due to the inherent small volumes or faceted surfaces and on the other hand conventional microscopic analysis techniques are not sufficiently sensitive. Here, we show that we can detect and map impurities at the ppm level in semiconductor nanowires using atom probe tomography. We develop a method applicable to a wide variety of nanowires relevant for electronic and optical devices. We expect that it will contribute significantly to the further optimization of the synthesis of nanowires, nanostructures and devices based on these structures.