Fire dynamics inside an open-plan compartment with an exposed CLT ceiling and glulam columns: CodeRed #01, Fire and Materials.
The desire by developers and architects to build mass timber buildings using cross laminated timber (CLT) and glulam has significantly increased globally in the last decade due to its benefits with regards to sustainability as well as other architectural and commercial drivers. This paper presents novel experimental evidence from CodeRed #02, the second in a series of large scale fire experiments carried out inside a purpose‐built, open‐plan compartment to capture fire dynamics in large compartments with exposed timber. The experiment used a continuous wood crib (6 × 29 m) as a controlled movable fuel load. The aim of the CodeRed #02 experiment was to study the impact of reduced ventilation on fire dynamics by keeping all other parameters the same as CodeRed #01 (Kotsovinos et al., 2022), with the exception of ventilation area which was reduced by almost half. The reduction in ventilation was found to significantly impact the fire dynamics by slowing the fire spread and burning rate. The reduced ventilation led to an increased fire duration by 4 min 30 s, which corresponds to 20% longer duration compared to CodeRed #01. The reduced ventilation had a greater overall impact on the rate of flame spread across the CLT (−23%) than the crib (−8%) compared to CodeRed #01. While the maximum temperature and incident heat fluxes inside the compartment were approximately the same as in CodeRed #01, their evolution in time and space were significantly different. The external flames were higher than in CodeRed #01 (3–3.5 m compared to 2.5–3 m) and protruded further laterally (up to ~4–5 m compared to ~1 m) outside of the compartment from the large end openings. Unlike CodeRed #01, the external flaming from CodeRed #02 pulsated between visible flames and dark soot with significantly greater frequency. This was caused by the limited ventilation resulting in incomplete combustion in CodeRed #02. The peak heat release rate of CodeRed #02 was estimated to be 16.5% lower than CodeRed #01, despite having the same fuel load. The average char depth in the ceiling, as measured at the end of the experiment, was 28 mm. This was 11% greater than in CodeRed #01 and was likely due to the increased duration of the fire. After the extinction of the flaming, smouldering occurred for CodeRed #02 as it did for CodeRed #01. One of the glulam columns lost its restraint and fell to the ground because smouldering spread through the thickness of the member. The findings from this work can help engineers quantify the hazard and therefore identify appropriate solutions for the fire safety design of exposed mass timber buildings.
The use of mass timber in construction is becoming a compelling option when faced with the high carbon footprint of traditional concrete and steel production. However, fire safety standards are yet to evolve to support these designs. Encapsulation is commonly used to protect all, or some, of the timber surfaces and reduce the risks introduced. This paper presents the results from CodeRed #04, the final experiment of the CodeRed experimental campaign. This experiment was carried out inside a purpose‐built facility to capture fire dynamics in large compartments with exposed timber. CodeRed #04 had identical characteristics to CodeRed #01 with the exception that ~50% of the cross‐laminated timber (CLT) ceiling was encapsulated. The experiments were intentionally similar to the traveling fire experiments, x‐ONE and x‐TWO, which had a non‐combustible ceiling to enable a direct comparison. The overall fire dynamics experienced in CodeRed #04, intersect the characteristics observed in CodeRed #01 and x‐ONE and x‐TWO.1. In CodeRed #04, there was a delay in the ignition of the CLT ceiling as the CLT directly above the crib was encapsulated. Once the CLT ceiling ignited, the fire spread rapidly throughout the compartment. The peak heat release rate (HRR) was estimated to be approximately 100 MW, a 17% decrease from CodeRed #01. Following CLT ignition the resulting fire duration, maximum temperatures, and heat fluxes were broadly similar to CodeRed #01. Flame heights of approximately 1.5 m were observed from the windows while flame heights of 2.5–3 m were observed in CodeRed #01. Therefore, flame heights were found to be comparable to x‐TWO.1, though over a greater number of windows, reflecting the greater extent of simultaneous burning within the compartment. The average charring depth of the exposed CLT panels was ~25 mm, which is similar to that measured in CodeRed #01‐suggesting that the fire severity near the ceiling was not strongly impacted by the 50% encapsulation of timber. No charring was observed where the ceiling was encapsulated and loaded service fixings installed through the encapsulation were found to be less likely to fail than when attached directly to the exposed timber. Smoldering was observed after the cessation of flaming and, in a few locations, was observed to progress through the thickness of the CLT panel and continue behind the encapsulation. This illustrates that, while encapsulation can succcessfully prevent flaming, it cannot be completely relied on to avoid smouldering. The findings from CodeRed #04 contribute to the development of evidence‐based fire safety design methodologies for exposed mass timber buildings.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.