We simulated and experimentally investigated the formation of periodic structures generated by multibeam interference patterning. The simulations at the different setup geometry show that resulting interference pattern is quasi-periodical. The calculated patterns show that the symmetries of the interference maxima depend mostly on the angles of incidence and that a wide variety of patterns can be obtained. Because of the difficulty in aligning four beams sufficiently well to avoid secondary periodicities, for testing we used a three-beam interference configuration. Atomic force microscopy images showed good correspondence between the experimental and simulated interference image, with flat islands which correspond to the destructive interference and narrow channels which correspond to the constructive interference fringes.

FePd alloys have recently attracted considerable attention as candidates for ultrahigh density magnetic storage media. In this paper we investigate FePd thin alloy film with a copper admixture composed of nanometer-sized grains. [Fe(0.9 nm)/Pd(1.1 nm)/Cu(d nm)]×5 multilayers were prepared by thermal deposition at room temperature in UHV conditions on Si(100) substrates covered by 100 nm SiO2. The thickness of the copper layer has been changed from 0 to 0.4 nm. After deposition, the multilayers were rapidly annealed at 600 °C in a nitrogen atmosphere, which resulted in the creation of the FePd:Cu alloy. The structure of alloy films obtained this way was determined by x-ray diffraction (XRD), glancing angle x-ray diffraction, and x-ray absorption fine structure (EXAFS). The measurements clearly showed that the L10 FePd:Cu nanocrystalline phase has been formed during the annealing process for all investigated copper compositions. This paper concentrates on the crystallographic grain features of FePd:Cu alloys and illustrates that the EXAFS technique, supported by XRD measurements, can help to extend the information about grain size and grain shape of poorly crystallized materials. We show that, using an appropriate model of the FePd:Cu grains, the comparison of EXAFS and XRD results gives a reasonable agreement.

No abstract

FePd thin films have been recently considered as promising material for high-density magnetic storage devices. However, it is necessary to find a proper method of fabrication for the (001)-textured and chemically well-ordered alloy. In this paper, we present the detailed investigations of lattice parameters, chemical order degree, grain sizes and crystallographic texture, carried out on FePd alloys with 10 at.% of Cu addition. The initial [Cu(0.2 nm)/Fe(0.9 nm)/Pd(1.1 nm)]x5 multilayers were thermally evaporated in an ultra-high vacuum on MgO(100), Si(100), Si(111) and Si(100) covered by 100 nm thick layer of amorphous SiO2. In order to obtain homogeneous FePd:Cu alloy, the multilayers were annealed in two different ways. First, the samples were rapidly annealed in nitrogen atmosphere at 600oC for 90 seconds. Next, the long annealing in a high vacuum for 1 hour at 700oC was done. This paper focuses on quantitative investigations of the chemical order degree and crystallographic texture of ternary FePd:Cu alloys deposited on four different substrates. In order to obtain both quantities we have taken a novel approach to consider the problem of dopant atoms located in the FePd structure. The studies of the structure were done using X-Ray Diffraction (XRD) performed with synchrotron radiation and pole figures measurements. We have found that the addition of Cu changes the FePd lattice parameters and lattice distortion. We have also shown, that using different substrates it is possible to obtain a FePd:Cu alloy with different chemical order and texture. Moreover, it was observed that texture category is substrate dependent

Ferromagnetic FePd L10 ordered alloys are highly expected as forthcoming high-density recording materials, because they reveal a large perpendicular magnetocrystalline anisotropy [1]. The value of the magnetic anisotropy of FePd alloy strongly depends on the alloy composition, degree of alloy order as well as on the crystallographic grain orientation. In particular, to obtain the perpendicular anisotropy, it is necessary to get the films with (001) texture. One of the successful methods, which allows one to obtain highly ordered alloy, is a subsequent deposition of Fe and Pd layers, followed by an annealing at high temperature. This paper presents the study of the FePd thin alloy film structure changing in the result of high temperature annealing. During the annealing in high vacuum, the measurements of electrical resistance were performed, indicating the regions of different structure evolution. Changes in the crystal structure and surface morphology induced by thermal treatment were investigated by X-ray diffraction, atomic force microscopy, as well as high resolution transmission electron microscopy and then compared with electrical resistivity measurement. The slow thermal annealing of the deposited layers leads to the formation of L1 0 ordered FePd alloy with preferred (111) grain orientation. After the annealing at the highest used temperature, the dewetting process was observed, resulting in a creation of well oriented, regular nanoparticles.