Ultrasonic Machining—a Comprehensive Review

Kumar, Jatinder

doi:10.1080/10910344.2013.806093

Cited by 107 publications

(72 citation statements)

References 113 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Most attention is given to the treatment of a thread with a small diameter [11]. A great effect on the processes of treating a thread by with the method of plastic deformation is exerted by a diameter of the hole [12,13].…”

Section: Literature Review and Problem Statementmentioning

confidence: 99%

Investigation of the process of thread extrusion using the ultrasound

Тurych

Weselowskaya

Rutkevych

et al. 2017

EEJET

View full text Add to dashboard Cite

V . R u t k e v y c hPhD* E-mail: v_rut@ukr.net S . S h a r g o r o d s k yPhD, Associate Professor* E-mail: serganatsharg@gmail.com *Department of Machinery and equipment for agricultural production Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008Досліджено та змодельовано процес видавлю вання різі з накладанням ультразвукових коли вань. На основі реологічної моделі деформування ідеального пружнопластичного тіла розробле ні залежності для розрахунку контактних тис ків та питомої сили тертя. Змодельовані кон тактні явища, що проходять в зоні деформації. Визначені оптимальні параметри видавлювання різі. Аналітично визначено діаметр отвору під видавлювання різі з накладанням ультразвуко вих коливань Ключові слова: ультразвукове видавлюван ня різі, частота коливань, амплітуда коливань, контактний тиск Исследован и смоделирован процесс выдавли вания резьбы с наложением ультразвуковых коле баний. На основе реологической модели деформи рования идеального упругопластического тела выведены зависимости для расчета контактных давлений и удельной силы трения. Смоделированы контактные явления, которые проходят в зоне деформации. Определены оптимальные парамет ры выдавливания резьбы. Аналитически опреде лен диаметр отверстия под выдавливание резьбы с наложением ультразвуковых колебаний Ключевые слова: ультразвуковое выдавлива ния резьбы, частота колебаний, амплитуда коле баний, контактное давление UDC 621.9.048.6

show abstract

Section: Literature Review and Problem Statementmentioning

confidence: 99%

Investigation of the process of thread extrusion using the ultrasound

Тurych

Weselowskaya

Rutkevych

et al. 2017

EEJET

View full text Add to dashboard Cite

show abstract

“…Erosion effect is produced through bombardment of abrasive particles directly against the work surface [12, 16,17,28,30,31,79,80,81,82]. Appropriate flow of slurry will enhanced the material removal rate [2,12,17,19,22,24,26,65]. Cavitation effect is also formed by slurry, which reduce the material removal rate [19,20,40,46].…”

Section: Traditional Ultrasonic Machiningmentioning

confidence: 99%

“…Cavitation effect is also formed by slurry, which reduce the material removal rate [19,20,40,46]. Material is removed in the form of micro-chips and flush out with slurry [20,22,46,65]. …”

Section: Traditional Ultrasonic Machiningmentioning

confidence: 99%

See 1 more Smart Citation

Mathematical Modeling for Material Removal and Optimization of Ultrasonic Drilling of Polycarbonate and Acrylic Glass for Surface Roughness by GRA Approach

Singh¹

2017

IJMEA

View full text Add to dashboard Cite

Abstract:Polycarbonate bullet proof and acrylic heat resistant glasses are used as the functional material in many industrial application. In automobile industries, banks and cabins, polycarbonate bullet proof glass has been used for security purpose. Similarly, acrylic heat resistant glass is used in furnace, microwaves, space craft and airplane applications. In this experimental research paper, Taguchi modal and Grey relational analysis are utilized for the ultrasonic drilling in these materials. For experimentation, input parameters are concentration, abrasive, grit size, power rating, hydrofluoric acid and tool materials. Output parameters are material removal rate, tool wear rate and surface roughness. In which, surface roughness is most significant output parameter, because it describe accuracy of the process. Through optimization analysis, Taguchi modal suggest that 40% abrasive concentration, mixture of (Alumina, Silicon carbide and Boron carbide) abrasive in 1:1:1, 600 grit of abrasive and 1.5% hydrofluoric acid gives best results for drilling in polycarbonate bullet proof glass material. Similarly, in acrylic heat resistant glass, mixture of Silicon carbide and Boron carbide (1:1), 600 grit abrasive and 1% hydrofluoric acid gives the optimum results. Concentration of slurry, abrasive grit size and hydrofluoric acid are the most significant parameters for ultrasonic drilling in both materials. Through Grey relational analysis the surface roughness is improved by 40% and 48% in polycarbonate (UL-752) and acrylic (BS-476) glass respectively.

show abstract

“…They reviewed effects of three input variables (rotational speed, feedrate, and ultrasonic power) on UVAG performances (cutting force, surface roughness, and edge chipping). Kumar et al (2013) made a comprehensive review for stationary USM and rotary mode USM as well as hybrid USM. Due to the advantage of UVAG, more UVAG research results have been reported after these review papers published, especially UVAG has been applied to new kinds of materials (like carbon fibre composites) and more input and output variables have been involved in experimental investigations.…”

Section: Introductionmentioning

confidence: 99%

Experimental investigations on core drilling by ultrasonic-vibration-assisted grinding for hard-to-machine materials - a review

Qin

Lei

Pei

2016

IJMR

View full text Add to dashboard Cite

Ultrasonic-vibration-assisted grinding (UVAG), a hybrid machining process combining material removal mechanisms of diamond grinding and ultrasonic machining, has been used to machine various hard-to-machine materials. Large amount of research work on UVAG has been carried out since it is invented. However there are few review papers to cover the current literature on UVAG. The emphasis of this literature review is the experimental investigations of the drilling process with ultrasonic vibration using a core drill with metal-bonded diamond abrasives. Experimental results are summarised and compared. The inconsistent results and their reasons are discussed. Furthermore, directions of future research on UVAG are also presented.

show abstract

Ultrasonic Machining—a Comprehensive Review

Cited by 107 publications

References 113 publications

Investigation of the process of thread extrusion using the ultrasound

Investigation of the process of thread extrusion using the ultrasound

Mathematical Modeling for Material Removal and Optimization of Ultrasonic Drilling of Polycarbonate and Acrylic Glass for Surface Roughness by GRA Approach

Experimental investigations on core drilling by ultrasonic-vibration-assisted grinding for hard-to-machine materials - a review

Contact Info

Product

Resources

About