Tris(ethylene diamine) nickel acetate as a promising precursor for hole transport layer in planar structured perovskite solar cells

Saranin, Danila; Mazov, Vsevolod N.; Luchnikov, Lev; Lypenko, D. A.; Gostishev, Pavel A.; Muratov, Dmitry S.; Podgorny, D. A.; Migunov, D. M.; Didenko, S.; Orlova, Marina; Кузнецов, Денис; Тамеев, А. Р.; Carlo, Aldo Di

doi:10.1039/c8tc01169a

Cited by 27 publications

(20 citation statements)

References 91 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Soon, better performances were obtained in the planar structure, where NiO hole selective layers (HSL) can be deposited using a vast range of techniques: sputtering, atomic layer deposition (ALD), e‐beam deposition, and NiO nanoparticles casting . The sol‐gel spin coating route is particularly appealing because of its low cost and because it offers the possibility to implement doping, by, e.g., copper, easily. Other doping elements, such as Li, Ag, Co, Zn, and Cs have also been successfully introduced into NiO, resulting in improved conductivity.…”

Section: Introductionmentioning

confidence: 99%

From Bulk to Surface: Sodium Treatment Reduces Recombination at the Nickel Oxide/Perovskite Interface

Girolamo

Phung

Jost

et al. 2019

Adv Materials Inter

Self Cite

View full text Add to dashboard Cite

The effect of sodium doping in NiO as a contact layer for perovskite solar cells is investigated. A combined X‐ray diffraction and X‐ray photoelectron spectroscopy analysis reveals that Na+ mostly segregates as NaOx/NaCl species around NiO crystallites, with the effect of reducing interface capacitance as revealed by impedance spectroscopy. Inspired by this finding, the NiO/perovskite interface in perovskite solar cells is modified via insertion of an ultrathin NaCl interlayer, which increases the NiO work‐function by 0.3 eV. This leads to an increase of power conversion efficiency, approaching 18%, and open‐circuit voltage due to a remarkable suppression of surface recombination, as revealed by photoluminescence analysis and light intensity–dependent electrical measurements.

show abstract

Section: Introductionmentioning

confidence: 99%

From Bulk to Surface: Sodium Treatment Reduces Recombination at the Nickel Oxide/Perovskite Interface

Girolamo

Phung

Jost

et al. 2019

Adv Materials Inter

Self Cite

View full text Add to dashboard Cite

show abstract

“…Different HTLs obtained depositing CuI on the top of NiO have been fabricated considering several concentrations of CuI (0.05 M; 0.10 M; 0.20 M) in acetonitrile. Both NiO [41] and CuI were deposited via spin coating (see the experimental section and the device architecture presented in Figure 1). Scanning electron microscopy (SEM) images of CuI film on NiO are reported in Figure 2 (from a to d).…”

Section: Resultsmentioning

confidence: 99%

“…The photoluminescence (PL) emission peak for the MAPbI 3 film (used as a reference on glass) and for HTL/ MAPbI 3 is shown in Figure 3b for the different single and double HTLs. By introducing the HTL, the MAPbI 3 PL emission is quenched [41] with respect to pristine MAPbI 3 . This effect is more pronounced in the presence of NiO/CuI HTL with comparison to single NiO HTL.…”

Section: Resultsmentioning

confidence: 99%

Copper Iodide Interlayer for Improved Charge Extraction and Stability of Inverted Perovskite Solar Cells

et al. 2019

Self Cite

View full text Add to dashboard Cite

Nickel oxide (NiO) is one of the most promising and high-performing Hole Transporting Layer (HTL) in inverted perovskite solar cells due to ideal band alignment with perovskite absorber, wide band gap, and high mobility of charges. At the same time, however, NiO does not provide good contact and trap-free junction for hole collection. In this paper, we examine this problem by developing a double hole transport configuration with a copper iodide (CuI) interlayer for efficient surface passivation. Transient photo-current (TPC) measurements showed that Perovskite/HTL interface with CuI interlayer has an improved hole injection; CuI passivation reduces the concentration of traps and the parasitic charge accumulation that limits the flow of charges. Moreover, we found that CuI protect the HTL/perovskite interface from degradation and consequently improve the stability of the cell. The presence of CuI interlayer induces an improvement of open-circuit voltage VOC (from 1.02 V to 1.07 V), an increase of the shunt resistance RSH (100%), a reduction of the series resistance RS (−30%), and finally a +10% improvement of the solar cell efficiency.

show abstract

“…Тонкие пленки перовскита MAPbI 3 были приготовлены одноступенчатым методом из MAI и PbI 2 [5]. Образованные пленки перовскита имели толщину ∼ 350 nm, обладали микрокристаллической структурой.…”

Section: металлоорганическиеunclassified

Фотоэлектрические параметры фотоприемников на основе тонких микрокристаллических пленок перовскита CH-=SUB=-3-=/SUB=-NH-=SUB=-3-=/SUB=-PbI-=SUB=-3-=/SUB=-

Amasev¹,

Savin²,

Николаев³

2020

Письма В Журнал Технической Физики

View full text Add to dashboard Cite

show abstract

Tris(ethylene diamine) nickel acetate as a promising precursor for hole transport layer in planar structured perovskite solar cells

Abstract: NiO/perovskite interface with novel NiO precursor was investigated with Auger profiling for solar cell with PCE > 15%.

Cited by 27 publications

References 91 publications

From Bulk to Surface: Sodium Treatment Reduces Recombination at the Nickel Oxide/Perovskite Interface

From Bulk to Surface: Sodium Treatment Reduces Recombination at the Nickel Oxide/Perovskite Interface

Copper Iodide Interlayer for Improved Charge Extraction and Stability of Inverted Perovskite Solar Cells

Фотоэлектрические параметры фотоприемников на основе тонких микрокристаллических пленок перовскита CH-=SUB=-3-=/SUB=-NH-=SUB=-3-=/SUB=-PbI-=SUB=-3-=/SUB=-

Contact Info

Product

Resources

About