Tribological Behaviour of Hemp, Glass and Carbon Fibre Composites

Fazio, Dario De; Boccarusso, Luca; Durante, Massimo

doi:10.1016/j.biotri.2019.100113

Cited by 29 publications

(15 citation statements)

References 38 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…These greatly enhanced the mechanical and tribological properties of the composites. Numerous works [19,25,29,31,33,37,61,66,71,73,77,80,84,89,91,93,102,104,107,109,112] have been reported in these regard. Alkali treatment by NaOH (sodium hydroxide) solution was the most commonly used due to the low cost and ease of use.…”

Section: Effect Of Chemical Treatmentmentioning

confidence: 99%

See 1 more Smart Citation

Biofiber‐reinforced polymeric hybrid composites: An overview on mechanical and tribological performance

Chandgude

Salunkhe

2020

Polymer Composites

View full text Add to dashboard Cite

This article presents a thorough review of biofiber-based hybrid composites along with the discussion on its mechanical and tribological performance in the polymeric matrix. Emphasis is centered on plant fibers as animal fibers are not frequently used and mineral fibers possess serious health issues. All five types of plant fibers and their hybrids are reviewed. Hybridization of plant fibers synergetically combines individual benefits while eliminating the limitations of single fiber use. Study regarding fiber origin, processability and extraction techniques, composition, chemical surface treatments, and applications are presented. Finally, the results obtained are summarized and future developments are discussed. The review concludes that biofiber hybrid composites possess great potential in several applications provided that satisfies design constraints and polymeric matrix compatibility issues.

show abstract

Section: Effect Of Chemical Treatmentmentioning

confidence: 99%

“…F I G U R E Coefficient of friction of some of the natural fibers/polymer composites. Adapted from References [19,37,39,61,68,73,79,84,87,104,108,116] [Color figure can be viewed at wileyonlinelibrary.com]…”

Section: Surface Modification Using Nanocellulosementioning

confidence: 99%

Biofiber‐reinforced polymeric hybrid composites: An overview on mechanical and tribological performance

Chandgude

Salunkhe

2020

Polymer Composites

View full text Add to dashboard Cite

show abstract

“…The components' properties directly affect the mechanical, physical, and frictional performance of the final CFMs [4,5]. As well as organic and inorganic fillers, the CFMs can be added with reinforcing materials such as basalt, carbon, glass fiber [2,6,7]. When the percentage by weight of the components used in producing such multi-component composite materials is selected appropriately, the improved structural properties expected from the final product can be obtained [6,8,9].…”

Section: Introductionmentioning

confidence: 99%

“…Finally, de Fazio et al studied the abrasion resistance of hemp fibers and compared it to glass and carbon fibre-reinforced composites. They have observed that natural fibers such as hemp fibers exhibit better abrasion behaviors than synthetic fibers [7].…”

Section: Introductionmentioning

confidence: 99%

Influence of ecological Juniperus Drupacea cone powder on mechanical and physical properties of fiber-reinforced composite friction materials

Aras¹,

Sepetcioglu

2022

European Mechanical Science

View full text Add to dashboard Cite

This work is aimed to study the mechanical and physical properties of composite friction materials (CFMs) produced by using various fiber types (glass, carbon, and basalt) filled and unfilled Organic Juniperus Drupacea Cone Powder (JDCP). The CFMs were tested by using a pin-on-disc tribo-test-rig under dry contact conditions. The JDCP gradually reduced the density of CFMs. The surface hardness of the CFMs exhibited a decreasing trend with the addition of JDCP filler. The presence of JDCP within the CFMs considerably increased the water and oil absorption. The results showed that the JDCP filled and unfilled basalt fiber reinforced CFMs had higher friction coefficients than JDCP filled and unfilled glass and carbon fiber reinforced CFMs. In addition, the friction coefficient of filled and unfilled carbon fiber reinforced CFMs was found to be the lowest. The tensile strengths obtained from the indirect tensile (Brazilian) test of basalt, glass and carbon fiber reinforced test CFMs increased with JDCP filler. In addition, the tensile strength of JDCP filled and unfilled carbon fiber reinforced FCMs proved to have better wear resistance than all other CFMs. The wear resistance of basalt, glass, and carbon fiber reinforced CFMs decreased with the increase of JDCP wt.% filler. Among JDCP filled and unfilled all CFMs, the highest wear resistance was detected in carbon fiber reinforced CFM. The minor wear resistance was seen in glass fiber reinforced CFMs than carbon and basalt reinforced samples.

show abstract

“…4 In industrially available lining compositions, binders, reinforcements, friction regulators, fillers and solid lubricants are used. In previous studies, it was observed that phenolic resin 2,[5][6][7][8][9][10][11][12][13][14][15][16][17][18][19] was used as binder material, different fiber type 7,9,10,12,14,15,17,[19][20][21][22] were used as reinforcement material, cashew dust 9,10,15,23 was used as friction adjuster, barite [6][7][8][9][10][11][12][13][14][15][16][17][18][19]21,22 was used as a filler and graphite 5,[7]…”

Section: Introductionmentioning

confidence: 99%

Optimization and assessment of brake pad production parameters and organic Juniperus drupacea cone powder additive ratio using the Taguchi method

Aras¹,

Tarakçıoğlu

2021

Journal of Composite Materials

View full text Add to dashboard Cite

In this study, an organic brake pad content was created to increase the overall tribological performance of the automobile brake system. Brake lining samples were obtained by hot molding method using juniperus drupacea cones powder which is not found in the literature in addition to barite, phenolic resin, fiber types (glass, carbon and basalt) and coke in the lining content. In order to determine the most ideal production conditions and content ratios, parameter combinations based on the L18(21 × 35) Taguchi orthogonal index were used according to the density, hardness, wear rate, friction coefficient objective functions. The density and hardness of the samples produced based on the orthogonal design were measured. A wear test was performed on a pin-on-disc type tribometer and the wear rate and friction coefficients were calculated according to the obtained values. Signal to noise ( S/N) ratio and ANOVA analysis were performed to determine the brake pad composition with the most ideal tribological properties. According to the results, the mixing time is 15 min., the molding temperature is 160 °C, the molding pressure is 100 MPa and the molding time is 15 min., have been found to be the optimum production conditions. In addition, it was observed that the density and hardness decreased as the amount of juniperus drupacea cone powder was increased. For this reason, it has been observed that the juniperus drupacea cone powder used for the first time in the brake lining composition can be used in lining content up to 25%, preferably up to 10% by weight.

show abstract

Tribological Behaviour of Hemp, Glass and Carbon Fibre Composites

Cited by 29 publications

References 38 publications

Biofiber‐reinforced polymeric hybrid composites: An overview on mechanical and tribological performance

Biofiber‐reinforced polymeric hybrid composites: An overview on mechanical and tribological performance

Influence of ecological Juniperus Drupacea cone powder on mechanical and physical properties of fiber-reinforced composite friction materials

Optimization and assessment of brake pad production parameters and organic Juniperus drupacea cone powder additive ratio using the Taguchi method

Contact Info

Product

Resources

About