Substrate-Integrated Waveguide Power Combiner/Divider Incorporating Absorbing Material

Huang, Yong Mao; Jiang, Wei; Jin, Haiyan; Zhou, Yuliang; Leng, Supeng; Wang, Guoan; Wu, Ke

doi:10.1109/lmwc.2017.2745488

Cited by 26 publications

(24 citation statements)

References 8 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Hence, the design of compact sub-6G filters is a hot research topic for mobile portable devices. Substrate integrated waveguide (SIW) is widely used in RF passive device designs due to low loss, low cost, and flexibility of integration properties, such as filter [1][2][3][4][5][6], antenna [7][8][9][10][11], phase shifter [12][13][14][15][16], power divider [17][18][19][20][21], and coupler [22][23][24][25][26]. However, SIW filters under 6 GHz is still outsize to meet the requirement of portable communication devices because of the long wavelength.…”

Section: Introductionmentioning

confidence: 99%

Design of a Compact 5.7-5.9 GHZ Filter Based on CRLH Resonator Units

Hu¹,

Gao²,

Xinlei³

et al. 2020

PIER Letters

View full text Add to dashboard Cite

A compact substrate integrated waveguide (SIW) filter based on composite right/lefthanded (CRLH) resonator units is implemented in this paper. The filter is composed of two CRLH resonator units serially connected by a SIW transmission line unit. The structure of the filter and equivalent circuit transmission behavior are analyzed, and a novel design method by optimizing the length and width of the interdigital metal slots to decrease the filter operation frequency is proposed. To further demonstrate the design theory and performance of the proposed filter, the filter was designed and fabricated on an RT6010 dielectric material. The measurement results show that the proposed filter works at a center frequency of 5.8 GHz with 200 MHz bandwidth The insertion loss is 2.3 dB, and the filter size is only 10 mm × 7.4 mm.

show abstract

Section: Introductionmentioning

confidence: 99%

Design of a Compact 5.7-5.9 GHZ Filter Based on CRLH Resonator Units

Hu¹,

Gao²,

Xinlei³

et al. 2020

PIER Letters

View full text Add to dashboard Cite

show abstract

“…Recently, most of the reported works are single ended‐to‐single ended (SETSE) 4‐7 . In Reference 4, a wideband power divider (PD) with arbitrary power division ratio (PDR) was presented with a tunability of PDR from 0.5:1 to 2:1 across wideband range of 60% and a controllable band from 35% to 63.2%.…”

Section: Introductionmentioning

confidence: 99%

“…In Reference 5, a new equivalent circuit model of an electrical size‐reduced coupled line radio frequency Marchand balun was proposed. In References 6,7, two design of substrate‐integrated waveguide (SIW) PDs were presented. Several balanced‐to‐single ended (BTSE) PDs are also reported lately.…”

Section: Introductionmentioning

confidence: 99%

A BTB UWB power divider with arbitrary power‐dividing ratio based on three‐slotline structure

Liu

Wei

Hou

et al. 2020

Int J RF Microw Comput Aided Eng

View full text Add to dashboard Cite

In this article, a balanced‐to‐balanced (BTB) ultra‐wide band (UWB) power divider (PD) is proposed, which can realize arbitrary power‐dividing ratio (PDR) with improved transmission bandwidth flatness. The proposed PD is primarily based on microstrip/slotline (MS) transition structures and parallel‐coupled three‐slotline structure. U‐type microstrip feed lines integrated with stepped‐impedance slotline resonators are adopted at the input and output ports, which make the differential‐mode (DM) responses independent of the common‐mode (CM) ones. Meanwhile, superior DM transmission and CM suppression are achieved intrinsically, thereby simplifying the design procedure significantly. By changing the distances between the coupled three slotlines, the PDR between the output ports is controllable. In order to verify the feasibility of the proposed design method, several prototype circuits of the proposed PDs with different PDRs are simulated and a prototype circuit with the 2:1 PDR is fabricated and measured. A good agreement between the simulation and measurement results is observed.

show abstract

“…Due to the need to meet the small size requirement of sub-6G portable devices, compact sub-6G filter design has become a hot research topic in recent years. Substrate integrated waveguides (SIWs) are widely used in RF (Radio Frequency) passive device designs due to their low loss and low cost and the flexibility of their integration properties, such as their filter [1][2][3][4][5][6], antenna [7][8][9], phase shifter [10][11][12][13][14], power divider [15][16][17][18], coupler [19][20][21][22], etc. However, SIW filters under 6 GHz are still too large to meet the requirement of portable communication devices because of their long wavelength.…”

Section: Introductionmentioning

confidence: 99%

A Compact 3.3–3.5 GHz Filter Based on Modified Composite Right-/Left-Handed Resonator Units

Zheng

et al. 2019

Electronics

View full text Add to dashboard Cite

In the RF (Radio Frequency) front-end of a communication system, bandpass filters (BPFs) are used to send passband signals and reject stopband signals. Substrate-integrated waveguides (SIW) are widely used in RF filter designs due to their low loss and low cost and the flexibility of their integration properties. However, SIW filters under 6 GHz are still too large to meet the requirement of portable communication devices due to their long wavelength. In this paper, a very compact fully integrated SIW filter is proposed and designed with RT6010 dielectric material to meet the small size requirement of portable devices for next-generation sub-6 G applications. The proposed filter contains two sawtooth-shaped composite right-/left-handed (CRLH) resonator units, instead of traditional rectangular-shaped CRLH resonator units, which makes the filter more compact and cost effective. The filter is designed and fabricated on an RT6010 substrate, with a size of only 10 mm × 7.4 mm. The measurement results illustrated that the proposed BPF shows a passband covering the frequency range of 3.25–3.45 GHz; the minimum passband insertion loss is only 2.4 dB; the stopband rejection is better than −20 dB throughout the frequencies below 3.0 GHz and above 3.8 GHz; S11 is as low as −37 dB at 3.35 GHz; and the group delay variation is only 1.4 ns throughout the operation bandwidth.

show abstract

Substrate-Integrated Waveguide Power Combiner/Divider Incorporating Absorbing Material

Cited by 26 publications

References 8 publications

Design of a Compact 5.7-5.9 GHZ Filter Based on CRLH Resonator Units

Design of a Compact 5.7-5.9 GHZ Filter Based on CRLH Resonator Units

A BTB UWB power divider with arbitrary power‐dividing ratio based on three‐slotline structure

A Compact 3.3–3.5 GHz Filter Based on Modified Composite Right-/Left-Handed Resonator Units

Contact Info

Product

Resources

About