Positron Methods for the Study of Defects in Bulk Materials

Abstract

Abstract:The basic principles of positron annihilation physics are briefly discussed and the three most important experimental techniques used for bulk studies are described (i.e. positron lifetime, angular correlation, Doppler broadening). Several examples of the use of the positron methods are discussed for metals, ceramics and molecular materials, which illustrate the sensitivity of the positron annihilation techniques to vacancy type defects. For example it is shown how information can be obtained about vacancy formation energies, vacancy migration and clustering, vacancy-impurity interactions, densities of rare gasses in bubbles in metals, and about free volume in molecular materials. 1.INTRODUCTIONThe positron is the antiparticle to the electron. This means that the positron has the same mass and spin as the electron, but has the opposite charge, viz. one positive elementary charge. Furthermore, if a positron is surrounded by one or more electrons the positron may annihilate with one of the electrons, i.e. both particles disappear and their masses are transformed into energy which is emitted as y-quanta, normally two or three. The properties of these y-quanta, such as their energies, emission directions, and time of emission which can all be measured, provide useful information about the material in which the positrons annihilate. Very briefly, this is the principle of the Positron Annihilation Spectroscopy.Positron Annihilation research is a very wide field as can be judged from the proceedings of the most recent international conferences [I-51 and other recent publications [6-101. In the present paper we shall concentrate on a discussion of the possibilities to study defects in solids, by giving exampIes for metals, ceramics and molecular materials. First, however, let us discuss some of the basic physical principles of positron annihilation and then describe the most important experimental techniques used in positron annihilation studies of defects in bulk materials.Article published online by EDP Sciences and available at http://dx.doi.org/10.1051/jp4:1995111 C1-94 JOURNAL DE PHYSIQUE IV POSITRONS IN SOLIDSIn conventional positron annihilation experiments the positrons are injected into a solid with a mean energy of the order of 200 keV. They slow down to thermal energies in about 10-12-10-1' sec (1-10 psec) by ionisation and excitation of the solid. During this time they penetrate a distance of 10-1000 pm depending on the density of the solid (the penetration depth is roughly inversely proportional to the density). Hence, the positrons probe bulk material in such experiments. In recent years a rapid development of a new technique has taken place, viz. of low-energy-positron beams. This technique will be discussed by others at this workshop [Ill. Annihilation of PositronsA positron that has been injected into a solid and has slowed down, in most cases annihilates with the emission of 2 y-quanta, since for free positrons the cross-section for emission of 3y is only 1/379 of the 2y cross-section. The ...

Studies on the role of ion mass and energy in the defect production in irradiation experiments in tungsten

“…The τ 1 values of both samples are in agreement with the theoretical value of 105 ± 3 ps, corresponding to the perfect W lattice [27]. The defect (vacancy) density of the recrystallized samples was calculated using the defect model of positrons [28] with a specific trapping rate of ∼4 × 10 14 s −1 [29]. (For the RC1 samples, the vacancy cluster density was found to be about 2.4 × 10 23 m −3 [18] whereas, for the RC2, it was about 5.03 × 10 23 m −3 ).…”

Influence of Physical Aging on the Molecular Motion and Structural Relaxation in Poly(ethylene terephthalate) and Related Polyesters

“…However, the distribution of free volume term, I 3 , was lower at 50 °C (Figure 16b), and the discrepancy was resolved by considering the product τ 3 3 I 3 (Figure 16c), which is indicative of the total hole size distribution in a material. 44,45 The total hole distribution in PET is surprisingly invariant compared with the usual time dependence observed for most amorphous polymers. The data show that complex processes are involved in terms of hole size changes with time and temperature but that the local free volume does not change significantly with temperature.…”

Accumulation of point defects and their complexes in irradiated metals as studied by the use of positron annihilation spectroscopy – a brief review

“…Pals is just one of several different PASs. A more detailed discussion of PAS can be found in e.g., [1,2] and references therein. In the present paper only results obtained by the positron lifetime technique will be reviewed to illustrate the potential of PAS.…”