Notifying and inspecting vehicle emission and temperature of vehicle engine

Kamalakar, Sneha S.; Vanjale, Mousami

doi:10.1109/icedss.2017.8073650

Cited by 4 publications

(2 citation statements)

References 6 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The publication of [35] examined the effect of an electrical component failure on performance and emissions, but in this case, it was also only a single component, the oxygen sensor. The advantage of the complexity of the measurements reported in this publication and its benefit is also evident when compared to the measurements reported in the publications [36][37][38][39][40].…”

mentioning

confidence: 79%

Influence of Engine Electronic Management Fault Simulation on Vehicle Operation

Šarkan

Loman

Synák

et al. 2022

Sensors

View full text Add to dashboard Cite

The preparation of the fuel mixture of a conventional internal combustion engine is currently controlled exclusively electronically. In order for the electrical management of an internal combustion engine to function properly, it is necessary that all its electronic components work flawlessly and fulfill their role. Failure of these electronic components can cause incorrect fuel mixture preparation and also affect driving safety. Due to the effect of individual failures, it has a negative impact on road safety and also negatively affects other participants. The task of the research is to investigate the effect of the failure of electronic engine components on the selected operating characteristics of a vehicle. The purpose of this article is to specify the extent to which a failure of an electronic engine component may affect the operation of a road vehicle. Eight failures of electronic systems (sensors and actuators) were simulated on a specific vehicle, with a petrol internal combustion engine. Measurements were performed in laboratory conditions, the purpose of which was to quantify the change in the operating characteristics of the vehicle between the faulty and fault-free state. The vehicle performance parameters and the production of selected exhaust emission components were determined for selected vehicle operating characteristics. The results show that in the normal operation of vehicles, there are situations where a failure in the electronic system of the engine has a significant impact on its operating characteristics and, at the same time, some of these failures are not identifiable by the vehicle operator. The findings of the publication can be used in the drafting of legislation, in the field of production and operation of road vehicles, and also in the mathematical modeling of the production of gaseous emissions by road transport.

show abstract

mentioning

confidence: 79%

Influence of Engine Electronic Management Fault Simulation on Vehicle Operation

Šarkan

Loman

Synák

et al. 2022

Sensors

View full text Add to dashboard Cite

show abstract

“…Notifying and checking vehicle emissions and vehicle engine temperatures investigated by Kamalakar. This proposed system helps to remind vehicle owners of some of these things: their carbon dioxide emissions; LPG gas leak if the vehicle is gas-operated; the engine temperature to avoid vehicle failure due to overheating of the vehicle engine [16]. The electronic nose to classify beef and pork using Naïve Bayes was investigated by Wijaya.…”

Section: Introductionmentioning

confidence: 99%

Design of gas concentration measurement and monitoring system for biogas power plant

Iswanto

Ma’arif

Kebenaran

et al. 2021

IJEECS

View full text Add to dashboard Cite

Biogas is a gas obtained from the breakdown of organic matter (such as animal waste, human waste, and plants) by methanogenic bacteria in an oxygen-free (anaerobic) state. The biogas produced mainly consists of 50-70% methane, 30-40% carbon dioxide, and other gases in small amounts. The gas produced has a different composition depending on the type of animal that produces it. It is challenging to obtain biogas concentration data because the monitoring equipment is currently minimal. Therefore, this research discusses how to make a monitoring system for biogas reactors. Sensors are installed in the digester tank and storage tank. The installed sensors are the MQ-4 sensor to detect methane gas (CH4), MG-811 sensor to detect carbon dioxide (CO2) gas, MQ-136 sensor to detect sulfide acid gas (H2S), and Thermocouple Type-K to detect temperature. The sensor will send a signal to the control unit in Arduino Mega 2560, then processed and displayed on the liquid crystal display (LCD). The sensor calculation results' accuracy is not much different from the reference based on the sensor readings. The sensor deviation standard is below 5.0, indicating that the sensor is in precision. The sensor's linearity of MQ-4 is 0.7%, the MG-811 is 0.17%, the MQ-136 is 0.29%, and the Type-K Thermocouple is 1.19%. The installed sensor can be used to monitor gas concentration and temperature in a biogas reactor.

show abstract