Investigation of Power Quality Improvement in Super Lift Luo Converter

Gnanavadivel, J.; Kumai, N Senthil; Priya, C.; Veni, K.S. Krishna

doi:10.11591/ijpeds.v8.i3.pp1240-1250

Cited by 12 publications

(3 citation statements)

References 18 publications

(9 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The inductors L1 and L2 discharges during this mode. The voltage pertaining to this mode are presented in (4) to (6).…”

Section: Proposed Converter Analysismentioning

confidence: 99%

An elevated gain DC-DC converter with active switched inductor for PV application

Mahalingam¹,

Gnanavadivel²

2023

IJPEDS

View full text Add to dashboard Cite

Innovative power electronic converters have emerged because of renewable energy expansion in the past two decades. Direct current DC grids can operate independently or connected to power grids. A DC grid has distributed generation (DG) units, such as solar panels and, fuel cells. It is necessary to have a DC-DC converter in DC grids to raise output voltage. Boost converters have limited voltage gain, and their switching stress is often equal to their output voltage. This work proposes a converter which gives high gain and less stress when compared to other recent converters. At 0.8 duty ratio, this converter produces an elevated gain of 59. An experimental prototype is built for the proposed converter and the results are presented.

show abstract

“…The inductors L1 and L2 discharges during this mode. The voltage pertaining to this mode are presented in (4) to (6).…”

Section: Proposed Converter Analysismentioning

confidence: 99%

An elevated gain DC-DC converter with active switched inductor for PV application

Mahalingam¹,

Gnanavadivel²

2023

IJPEDS

View full text Add to dashboard Cite

show abstract

“…DC-DC converters can be used as power supplies which convert AC supply to any number of suitable DC voltages to power computer peripherals [1]. Also, DC-DC converters are widely used in industrial applications, vehicle auxiliary power supplies, Electric vehicles etc [2]- [6].…”

Section: Introductionmentioning

confidence: 99%

Performance evaluation of SEPIC, Luo and ZETA converter

Siddharthan

Balasubramanian

2019

IJPEDS

View full text Add to dashboard Cite

<p><span>DC-DC converters are devices which convert direct current (DC) from one voltage level to another by changing the duty cycle of the main switches in the circuits. These converters are widely used in switched mode power supplies and it is important to supply a constant output voltage, regardless of disturbances on the input voltage. In this work, the performance of three different converters such as Single-Ended Primary-Inductance Converter (SEPIC), Luo converter and ZETA converter have been analyzed. Further, the parameters values such as ripple voltage, switching losses and efficiency of the proposed three different converters were compared with each other. Also, the simulation work has been carried out using MATLAB/SIMULINK software. From the comparison of obtained results, it is observed that the ZETA converter has high significance than the SEPIC and Luo converter.</span></p>

show abstract

“…Need of perfect output at the DC stage during continuous conduction requires low THD and high input power factor at AC input side [27]. Luo topology of AC to DC conversion is used for power quality improvement with hysteresis controller to achieve high power factor along with supply current harmonic distortions of less than 5% [13]. THD analysis for various load conduction of AC to DC three level converter with a help of different controller tuners such as PI, Fuzzy tuned PI controller, the comparative results for each controller provides optimised result [11].…”

Section: Introductionmentioning

confidence: 99%

Power Quality Analysis of Single Phase Full Bridge Rectifier Fed DC Motor Drive

K¹,

Siddharthan²,

Saiayyappa³

2018

International Journal of Innovative Research in Electrical, Ele

View full text Add to dashboard Cite

This paper provides a power quality analysis of single phase full bridge rectifier fed DC motor drive. A single phase full bridge rectifier is generally used in low voltage distribution system. It is necessary to analyse harmonic level and power factor. Here, DC motor is considered as the rectifier's load. The THD and power factor analysis is done for different loading conditions. The first analysis is based on variation of delay angle and its effect on THD and power factor. The second analysis is based on variation of torque or the changes in mechanical load done in the motor while maintaining the delay angle as constant. These analyses are useful in quantizing the THD and power factor at various conditions. FFT analysis on the input current provides the information about the various harmonics present in the waveform. The overall analysis is done using MATLAB software.

show abstract

Investigation of Power Quality Improvement in Super Lift Luo Converter

Cited by 12 publications

References 18 publications

An elevated gain DC-DC converter with active switched inductor for PV application

An elevated gain DC-DC converter with active switched inductor for PV application

Performance evaluation of SEPIC, Luo and ZETA converter

Power Quality Analysis of Single Phase Full Bridge Rectifier Fed DC Motor Drive

Contact Info

Product

Resources

About