Experimental studies of glued Aluminum-glass joints

Ligaj, Bogdan; Wirwicki, Mateusz; Karolewska, Karolina; Jasińska, A.

doi:10.1088/1757-899x/344/1/012014

Cited by 8 publications

(6 citation statements)

References 7 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In researches were used new type of specimen, being the subject of a patent application in Poland ( Figure 1) [13]. The sample consist of two beams: top one with coarseness g1 and bottom one with coarseness g2, which were made of construction material.…”

Section: Research Objectmentioning

confidence: 99%

Experimental studies of adhesive joints in four-point static bending

Jasińska

Ligaj

Mazurkiewicz

2018

IOP Conf. Ser.: Mater. Sci. Eng.

Self Cite

View full text Add to dashboard Cite

Abstract.A new type of specimens, being the subject of the patent application in Poland, was used in the studies. The sample consists of two beams: top one (longer) made of structural material such as steel, aluminium alloy and bottom one (shorter), which is part of the glass, which is tempered, layered or traditional glass. The top beam may have any cross-section, e.g. rectangular, square, c-shaped, etc., which is characterized by different values of the moment of inertia. The bottom beam, meanwhile, is made of rectangular glass. The tests were performed under four-point bending conditions at monotonic incremental bending moment values on the Instron 5965 durability machine. The sample allows bending tests to be performed at bending loads while maintaining a constant bending moment in the glued joint area. The new type of specimen has been developed to allow for the testing of glued joints of different structural rigidity, with special emphasis on the steel-glass, aluminum-glass, steel-aluminum and similar connections. The experimental study of the durability of adhesive joints under four-point bending conditions with the monotonic incremental bending moment allows to determine the values of stresses, whose value is related to initiation of damage of the tested joint.

show abstract

Section: Research Objectmentioning

confidence: 99%

Experimental studies of adhesive joints in four-point static bending

Jasińska

Ligaj

Mazurkiewicz

2018

IOP Conf. Ser.: Mater. Sci. Eng.

Self Cite

View full text Add to dashboard Cite

show abstract

“…Examples of experimental test results are included in the work carried out by [ 3 , 4 ]. Other non-standard research methods for adhesive joints are presented in the work carried out by [ 5 , 6 ]. They involve the application of a “sandwich”-type specimen which is subjected to four-point bending.…”

Section: Introductionmentioning

confidence: 99%

Verification of Selected Failure Criteria for Adhesive Bonded Elements with Different Stiffness through the Use of Methacrylic Adhesive

et al. 2020

View full text Add to dashboard Cite

This study presents the testing results of methacrylic adhesive single-lap joints made from elements with different stiffness and of the adhesive itself, using cast specimens. Methods for the preparation and testing of material specimens of the adhesive joints have been presented. Moreover, an attempt was undertaken to determine the strength criterion and find out which of the presented calculation methods enables the most precise assessment of strength in the tested group of single-lap joints, that differ in terms of the adhered stiffness and thickness. For this purpose, C45 steel and 5754 aluminium flat bars were bonded. Stress distributions were determined for failure forces obtained in the experiment by means of three basic analytic and numerical methods. Stress and strain states were compared, indicating the highest consistency for the value of normal peel stresses acting in the direction perpendicular to the direction of the joint tension. Reduced stresses provided by the analyses reached values higher than those which were achieved during the specimen tension testing.

show abstract

“…Aluminum alloy is increasingly used in the construction of machine components (Ligaj et al, 2018). This is due to the lower density of the aluminum alloy (2.65 -2.85 g/cm 3 ) compared to the density of steel (7.86 g/cm 3 ).…”

Section: Introductionmentioning

confidence: 99%

Strength of Welded Joints Made of Aw-5754 Alloy Under Static Load Conditions

Grączewski¹,

Ligaj²,

Giętka³

2020

Engineering Mechanics 2020

View full text Add to dashboard Cite

The most commonly used method of aluminum welding is gas arc welding using a fusible electrode (MIG method) and a non-fusible electrode (TIG method). In machine construction aluminum alloys are commonly used, which the 5xxx series alloys are characterized by high strength and corrosion resistance. The work presents the properties of EN AW-5754 alloy, which is a material that allows joining elements by welding. The aim of the paper is to present mechanical properties test results of EN AW-5754 alloy welded joints with the 131 method for various values of linear welding energy: Q = 70 kJ/mm and Q = 1280 kJ/mm. The obtained results indicate a significant influence of linear welding energy on the strength of the welded joint.

show abstract

Experimental studies of glued Aluminum-glass joints

Cited by 8 publications

References 7 publications

Experimental studies of adhesive joints in four-point static bending

Experimental studies of adhesive joints in four-point static bending

Verification of Selected Failure Criteria for Adhesive Bonded Elements with Different Stiffness through the Use of Methacrylic Adhesive

Strength of Welded Joints Made of Aw-5754 Alloy Under Static Load Conditions

Contact Info

Product

Resources

About