Development of new hybrid jute/carbon/fishbone reinforced polymer composite

Singh, Harsimran; Batra, Neera; Dikshit, Iti

doi:10.1016/j.matpr.2020.05.520

Cited by 17 publications

(10 citation statements)

References 16 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Such evidence can be further deduced from Figure 13 . The 0° raster angle during printing definitively optimizes the tensile properties, confirming data from the literature, obtained on similar systems, where 0° raster angle usually optimizes tensile properties, whereas 45° leads to optimization of flexural and impact properties [ 10 , 26 , 32 , 33 ].…”

Section: Resultssupporting

confidence: 81%

Green Composites Based on Mater-Bi® and Solanum lycopersicum Plant Waste for 3D Printing Applications

2023

View full text Add to dashboard Cite

3D printability of green composites is currently experiencing a boost in importance and interest, envisaging a way to valorise agricultural waste, in order to obtain affordable fillers for the preparation of biodegradable polymer-based composites with reduced cost and environmental impact, without undermining processability and mechanical performance. In this work, an innovative green composite was prepared by combining a starch-based biodegradable polymer (Mater-Bi®, MB) and a filler obtained from the lignocellulosic waste coming from Solanum lycopersicum (i.e., tomato plant) harvesting. Different processing parameters and different filler amounts were investigated, and the obtained samples were subjected to rheological, morphological, and mechanical characterizations. Regarding the adopted filler amounts, processability was found to be good, with adequate dispersion of the filler in the matrix. Mechanical performance was satisfactory, and it was found that this is significantly affected by specific process parameters such as the raster angle. The mechanical properties were compared to those predictable from the Halpin–Tsai model, finding that the prepared systems exceed the expected values.

show abstract

Section: Resultssupporting

confidence: 81%

Green Composites Based on Mater-Bi® and Solanum lycopersicum Plant Waste for 3D Printing Applications

2023

View full text Add to dashboard Cite

show abstract

“…It can be seen from the results in the graph, hybridization of jute fibers with low mechanical features with high strength carbon fibers caused a significant increase in the hardness value. In addition, it has been found in previous studies that conditions that cause weak bonds between the matrix and the reinforcement, such as the addition of filler, lead to a decrease in the hardness value in carbon fiber composites [39,40]. In terms of the use of resins, the JCE composite structure has a 6.36% higher microhardness value than the JCP composite structure in hybrid composites.…”

Section: Hardness Test Resultsmentioning

confidence: 95%

The Effect of Use of Different Types of Matrix Material on Mechanical Characteristics in Jute/Carbon Fiber Reinforced Hybrid Composites

KARAÇOR¹,

Özcanlı²

2022

Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi

View full text Add to dashboard Cite

“…Figure 1 shows the methodology to prepare the composite, it was similar as adopted in our previous study. [ 38–40 ] The material preparation was performed in two‐phase, in the first phase, the porcine bone (age 3–7 years) was procured from the local butcher shop and thoroughly washed and sun‐dried for 2 to 3 days. Later the bones were put in the oven at 60°C for an hour to remove the moisture from them.…”

Section: Methodsmentioning

confidence: 99%

Experimental investigations and optimization of tensile and impact strength of a novel composite reinforced with carbon jute and porcine bone powder

Dikshit

Bhushan

2022

Polymer Composites

Self Cite

View full text Add to dashboard Cite

Mechanical properties like tensile strength and impact strength play a significant role in the development of composites and composites with lightweight and improved mechanical properties are desirable. In the current research work, a novel composite consisting of carbon, jute, and porcine bone powder is fabricated using compression molding techniques. The experimentation was carried out as per the central composite design (CCD) of response surface methodology (RSM). Before experimentation, the jute fibers were treated with sodium hydroxide solution (NaOH) to achieve better adhesion with the polymer matrix. The composite was fabricated at different input parameters viz.: NaOH concentration, PBP size, and PBP wt%, whereas tensile strength and impact strength are considered as performance characteristics. Moreover, a statistical approach (i.e., ANOVA) was applied to determine the significant parameters and their influence on the performance characteristics. All the experiments were conducted as per ASTM standards. Fourier transform infrared (FTIR) spectroscopy was performed to analyze the effect of NaOH treatment on jute fiber, and scanning electron microscopy (SEM) images were used to perform the fractographic analysis. The study revealed that among the various parameters, NaOH % has the most significant influence on tensile strength (39.7%) and impact strength (37.8%). Further, optimization was performed using genetic programming, and an improvement of tensile strength by 10% and impact strength by 15% was observed.

show abstract

Development of new hybrid jute/carbon/fishbone reinforced polymer composite

Cited by 17 publications

References 16 publications

Green Composites Based on Mater-Bi® and Solanum lycopersicum Plant Waste for 3D Printing Applications

Green Composites Based on Mater-Bi® and Solanum lycopersicum Plant Waste for 3D Printing Applications

The Effect of Use of Different Types of Matrix Material on Mechanical Characteristics in Jute/Carbon Fiber Reinforced Hybrid Composites

Experimental investigations and optimization of tensile and impact strength of a novel composite reinforced with carbon jute and porcine bone powder

Contact Info

Product

Resources

About