Development of a method of partial discharge detection in extra-high voltage cross-linked polyethylene insulated cable lines

Katsuta, G.; Toya, A.; Muraoka, K.; Endoh, Takeshi; Sekii, Y.; Ikeda, C.

doi:10.1109/61.141815

Cited by 59 publications

(12 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…A feeder going out of substation to low voltage (LV) transformers, usually is not a single cable route. This feeder is divided into a number of shorter sections and branches of cables that interconnected by ring main units (RMUs [28], time of arrival analysis (TOA) [29] and frequency-amplitude analysis (FAA) [30]. These techniques are useful for single route cables, however due to certain limitations they are not suitable for multipath cable networks.…”

Section: Detectionmentioning

confidence: 99%

Electromagnetic sensing for predictive diagnostics of electrical insulation defects in MV power lines

et al. 2015

View full text Add to dashboard Cite

Section: Detectionmentioning

confidence: 99%

Electromagnetic sensing for predictive diagnostics of electrical insulation defects in MV power lines

et al. 2015

View full text Add to dashboard Cite

“…The sensor is some kind of a foil sensor applying the partial discharge measurement for conventional XLPE cables [7].…”

Section: Electrical Propertiesmentioning

confidence: 99%

Demonstration and Verification Tests of 500 m Long HTS Power Cable

Takahashi

Suzuki

Ichikawa

et al. 2005

IEEE Trans. Appl. Supercond.

View full text Add to dashboard Cite

A high-temperature superconducting (HTS) power transmission cable is considered as one of the next-generation power transmission technologies. The introduction of HTS cables into the actual power grid requires a long-distance cooling tube, due to the location of the cooling stations at intervals of several kilometers along the cable length. Therefore, it is essential to understand the flow property of the liquid nitrogen as a coolant for the HTS cable, the current flow properties, electrical insulation characteristics, thermal insulation properties and mechanical behavior for the HTS cable taking into account its long length. This paper provides a brief summary of the HTS cable test system with a length of 500 m constructed in the Yokosuka area of CRIEPI.

show abstract

“…Partial discharges commonly occur in power cables such as those made from cross-linked polyethylene (XLPE) [5][6][7][8]. Therefore, analyses of partial discharge activities within power cables have to be carried out periodically to monitor the insulation performance of the cables.…”

Section: Introductionmentioning

confidence: 99%

Partial Discharge Characteristics in LLDPE-Natural Rubber Blends: Correlating Electrical Quantities with Surface Degradation

Aulia

Ahmad²,

Abdul‐Malek³

et al. 2016

Journal of Electrical Engineering and Technology

View full text Add to dashboard Cite

-Partial discharges (PD) lead to the degradation of high voltage cables and accessories. PD activities occur due to the existence of impurities, voids, contaminants, defects and protrusions during the manufacture and installation of power cables. Commonly, insulation failures occur at cable joints and terminations, caused by inhomogeneous electric field distributions. In this work, a blend of natural rubber (NR) and linear low density polyethylene (LLDPE) was investigated, and the optimal formulation of the blend that could resist PD was discussed. The experiments were conducted under a constant high voltage stress test of 6.5 kV AC and the magnitude of partial discharge activities was recorded using the CIGRE method II. Pattern analysis of PD signals was performed along with the interpretation of morphological changes. The results showed that the addition of 10 wt% of NR and 5 wt% of Alumina Trihydrate (ATH) provided promising results in resisting PD activities. However, as the NR content increased, more micropores existed, thus resulting in increased PD activities within the samples.

show abstract

Development of a method of partial discharge detection in extra-high voltage cross-linked polyethylene insulated cable lines

Cited by 59 publications

References 9 publications

Electromagnetic sensing for predictive diagnostics of electrical insulation defects in MV power lines

Electromagnetic sensing for predictive diagnostics of electrical insulation defects in MV power lines

Demonstration and Verification Tests of 500 m Long HTS Power Cable

Partial Discharge Characteristics in LLDPE-Natural Rubber Blends: Correlating Electrical Quantities with Surface Degradation

Contact Info

Product

Resources

About