Calorimetric Methods

Gaune‐Escard, M.

doi:10.1007/978-94-010-0458-9_16

Cited by 17 publications

(15 citation statements)

References 46 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…NETZCH Proteus-Thermal Analysis-version 5.2.1 software was used for processing the DTA-TG experiment. The DTA peaks were established on the heating curve along with the transformation enthalpy [28,29,[38][39][40].…”

Section: Equipmentmentioning

confidence: 99%

Characterization of Aluminum Alloy–Silicon Carbide Functionally Graded Materials Developed by Centrifugal Casting Process

et al. 2021

View full text Add to dashboard Cite

The continuous development of modern industries rises the necessity for functionally graded materials. This research starts from the consideration that the incorporation of SiC particles in the molten aluminum alloy can be difficult due to the very low wettability of SiC particles. In order to increase their wettability, SiC particles were covered with a layer of metallic copper. The incorporation of SiC particles into the aluminum alloy mass was performed by centrifugal casting. The secondary hypoeutectic Al-Si alloy used in this study was elaborated within the crucible of a resistors heated furnace. The metallic coating of SiC particles, in addition to the effect of increasing their wettability by molten metal, also has a role in preventing the formation of aluminum carbide in case of heating above 700 °C. A great amount of attention was paid to the parameters used during the centrifugal casting process. The results showed that adjusting the proportion of SiC particles within the composite allows us to obtain values of the thermal expansion coefficient within previously established limits. The present work demonstrates that the coating of SiC particles covered with a thin layer of metallic Cu creates the conditions to easily incorporate them into the molten Al mass, thus obtaining FGMs with controlled properties.

show abstract

Section: Equipmentmentioning

confidence: 99%

Characterization of Aluminum Alloy–Silicon Carbide Functionally Graded Materials Developed by Centrifugal Casting Process

et al. 2021

View full text Add to dashboard Cite

show abstract

“…By contrast, the low temperature ionic liquid field, the subject of the present volume, is very much in its formative stages. The many studies on the interesting transport properties of ionic liquids and thermodynamic properties have focused mainly on characterizing new systems for potential applications [1][2][3][4][5]. The job of placing ion conductive behavior within the wider phenomenology of liquid and amorphous solid electrolytes, and of the liquid state in general, has barely begun.…”

Section: Classes Of Ionic Liquidsmentioning

confidence: 99%

Physical Chemistry of Ionic Liquids, Inorganic and Organic, Protic and Aprotic

Angell

Yoshizawa

et al. 2005

Electrochemical Aspects of Ionic Liquids

View full text Add to dashboard Cite

“…3). The first one, very sharp, starts at 726 C while the second one starts at the end of the first effect, i. e. around 810 C. This second peak has a typical shape [9] and corresponds closely to the peritectic decomposition temperature observed by Thoma [8].…”

Section: Resultsmentioning

confidence: 84%

Preliminary Studies of the Obtaining of Solid Metallic Cerium from Fluoride Melts

Popescu

Zuca

2003

Zeitschrift Für Naturforschung A

View full text Add to dashboard Cite

The present study deals with the obtaining of solid cerium by molten salt electrolysis of a 46.74 -48.26 -5wt% LiF-NaF-NaCeF 4 mixture, in the temperature range 700 -730 C and with a current efficiency of 75%.For this purpose NaCeF 4 was obtained, characterized and it's cubic form was identified. The solubility and decomposition potential of this compound in the molten electrolyte 49.2 -50.8% LiF-NaF was also studied.

show abstract

Calorimetric Methods

Cited by 17 publications

References 46 publications

Characterization of Aluminum Alloy–Silicon Carbide Functionally Graded Materials Developed by Centrifugal Casting Process

Characterization of Aluminum Alloy–Silicon Carbide Functionally Graded Materials Developed by Centrifugal Casting Process

Physical Chemistry of Ionic Liquids, Inorganic and Organic, Protic and Aprotic

Preliminary Studies of the Obtaining of Solid Metallic Cerium from Fluoride Melts

Contact Info

Product

Resources

About