The AlCrFeCoNi high entropy alloy exhibits unexpected properties that can be obtained after mixing five different elements, which could not be obtained from any one independent element. The difference to conventional alloys is that these alloys may have, at the same time, both hardness and plasticity, can be used in severe impact applications. In order to study the influence of aluminum content on the microhardness and microstructure of the high entropy alloys AlxCrFeCoNi (x: atomic ratio, x= 0.2 to 2.0) nine types of samples were obtained as mini-sized ingots (50x15x9.5 mm and 40 g weight). The mini-ingots were obtained using arc melt casting process in a vacuum arc remelting device (VAR MRF ABJ 900). The influence of the chemical elements on the microstructure, phases morphology and microhardness of AlxCrFeCoNi system was studied. The results have confirmed that mechanical properties could be greatly adjusted by the chemical composition change. The main element that influences the microhardness of the analyzed system is aluminum, due to the formation of Al-Fe compounds with high hardness. Increasing the aluminum content in the alloy to values greater than 1.8 ... 2 at.% contribute to the increase of hardness and also to the embrittlement thereof. Other elements like Cr, Fe, Co and Ni can contribute to mitigate increasing the hardness of the alloy. The type of phases formed in high entropy alloy are dependent to the aluminum concentration. So, depending on of aluminium content, different phases are obtained, like FCC for low Al content, mixture of FCC and BCC for about 2.5 %Al and BCC for high Al content. The crystallite size depends on the chemical composition and increase with the aluminium content.

This paper presents and discusses research conducted with the purpose of developing the use of solar energy in the heat treatment of steels. For this, a vertical axis solar furnace called at Plataforma Solar de Almeria was adapted such as to allow control of the heating and cooling processes of samples made from 1.1730 steel. Thus temperature variation in pre-set points of the heated samples could be monitored in correlation with the working parameters: the level of solar radiation and implicitly the energy used the conditions of sample exposed to solar radiation, and the various protections and cooling mediums.The recorded data allowed establishing the types of treatments applied for certain working conditions. The distribution of hardness, as the representative feature resulting from heat treatment, was analysed on all sides of the treated samples. In correlation with the time-temperature-transformation diagram of 1.1730 steel, the measured values confirmed the possibility of using solar energy in all types of heat treatment applied to this steel. In parallel the efficiency of using solar energy was analysed in comparison to the energy obtained by burning methane gas for the heat treatment for the same set of samples. The analysis considered energy consumption, productivity and the impact on the environment. Thanks to various data obtained through developed experiences, which cover a wide range of thermic treatments applied steels 1.1730 model, we can certainly state that this can be a solid base in using solar energy in applications of thermic treatment at a high industrial level.

No abstract

No abstract

The appropriate selection of implant materials is very important for the long-term success of the implants. A modified composition of AISI 316 stainless steel was treated using solar energy in a vertical axis solar furnace and it was subjected to a hyper-hardening treatment at a 1050 °C austenitizing temperature with a rapid cooling in cold water followed by three variants of tempering (150, 250, and 350 °C). After the heat treatment, the samples were analyzed in terms of hardness, microstructure (performed by scanning electron microscopy), and corrosion resistance. The electrochemical measurements were performed by potentiodynamic and electrochemical impedance spectroscopy in liquids that simulate biological fluids (NaCl 0.9% and Ringer’s solution). Different corrosion behaviors according to the heat treatment type have been observed and a passivation layer has formed on some of the heat-treated samples. The samples, heat-treated by immersion quenching, exhibit a significantly improved pitting corrosion resistance. The subsequent heat treatments, like tempering at 350 °C after quenching, also promote low corrosion rates. The heat treatments performed using solar energy applied on stainless steel can lead to good corrosion behavior and can be recommended as unconventional thermal processing of biocompatible materials.

No abstract

No abstract

No abstract