На сегодняшний день существует риск разрушения для большого количества зданий от различных аварийных ситуаций. Современная нормативная база проектирования и эксплуатации зданий, содержит многолетний опыт анализа причин обрушения, учитывает большое количество воздействий на конструкции (динамические нагрузки, климатические воздействия, временные и постоянные) в течении всего срока службы. Однако возрастающее количество аварий, с разной степенью разрушений, как отдельных частей, так и всего строения, говорит о том, что воздействие, вызвавшее разрушение, не было учтено в нормативных документах, на основании которых был спроектирован объект. Поэтому возникает необходимость в точных расчетных алгоритмах, современных надежных и экономически выгодных методиках по конструктивному усилению несущих каркасов зданий.В статье рассмотрены существующие методы, для прогнозирования эффектов разрушения и решения задач на определение напряженно-деформированного состояния исходя из специально разработанной модели прочности RHT (Riedel-Hiermaier-Thoma) для высокоскоростного деформирования железобетона в условиях динамического нагружения.Рассмотрена модельная задача с использованием вариационного подхода, основанного на построении функционала расчета мощности упругой деформации с учетом мощности сил инерции для заряда взрывчатого вещества сферической формы, расположенного непосредственно перед сооружением. Все расчеты производились в среде ANSYSLS-DYNA, получены результаты в форме графиков скоростей деформаций и полей напряжений.Ключевые слова: динамическое нагружение, напряженно-деформированное состояние, взрывчатые вещества, энергетический метод, метод конечных элементов, железобетон.Библиография: 22 названия.
The paper proposes the development of the mathematical variational Hashin-Strickman method, which was previously used to determine the maximum possible values of effective elastic characteristics. In this case, the effective plasticity characteristics of two-component composites are determined. In particular, the fork of possible values of the effective yield strength of such composite materials is determined.
Николай Михайлович Добровольский -доктор физико-математических наук, профессор, Тульский государственный педагогический университет им. Л.Н. Толстого (г. Тула).Ольга Владимировна Кузовлева -кандидат технических наук, доцент, Российский государственный университет правосудия (г. Москва).
Ключевые слова: пористый материал на основе меди, сигмоидально-ступенчатые закономерности трения, смазочная композиция, трение, фторированный графен.Библиография: 23 названия.
Аннотация В статье рассмотрено взаимодействие водорода с дефектами кристаллического строения в металлах и сплавах. Приведена классификация водородных ловушек с точки зрения их энергетических уровней. Рассмотрены различные виды взаимодействий водо-родных ловушек, в зависимости от их энергии связи. Изучено влияние водородных ло-вушек на коэффициент диффузии водорода в стали. Показано, что наличие в металлах высокоэнергетических водородных ловушек приводит к снижению диффузионной по-движности водорода, который тем самым исключается из процесса охрупчивания. Ключевые слова: водородное охрупчивание, водородные ловушки, диффузия водорода, энергия связи, дислокации, границы раздела. Библиография: 44 названия.
The article considers the influence of the quality of the initial charge on the structure and physical and mechanical properties of the structural medium-alloy steel 30KhGSA. It was found that the 30KhGSA steel (smelters No. 3-4) cast in cast-iron molds (ingot weight 2.6 t) has a significant chemical heterogeneity and liquation in carbon and the main alloying elements (Cr and Mn), and in the melting on the semi-product of the boiling slag layer, the liquation is more pronounced. Starting from the tempering temperature of 500 ∘ C, the structure of both melts (the fluidized slag layer and the ordinary metallized charge) becomes more uniform and the mechanical properties are aligned. Microstructural studies have established that with an increase in the annealing temperature at a single exposure, the chemical inhomogeneity decreases, but not significantly. Starting from 1000 ∘ C, when the annealing temperature increases, the steel grain diversity and the growth of austenitic grains appear, especially in the melting on the semi-product of the boiling slag layer. Different grain sizes adversely affect the mechanical properties of steel: grain enlargement reduces the resistance of steel to brittle fracture, worsens the service characteristics of the metal. Elimination of chemical and structural heterogeneity can be achieved by conducting a ho-mogenizing annealing (annealing at 950 ∘ C for 8 hours). An increase in the annealing temperature leads to an intensive grain growth, especially in steel smelted on the original charge. It is shown that 30XGSA steel, which is melted on a semi-product of a boiling slag layer, in an improved state with equal hardness and strength characteristics, has increased plastic properties and especially impact strength in comparison with steel on a conventional metallized charge. Apparently, this should also determine the higher operating characteristics of steel obtained with the use of pure primary charge.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.