Реферат. Изучено влияние цинкосодержащих технологических добавок при частичной замене оксида цинка и стеариновой кислоты на деформационно-прочностные и эксплуатационные свойства шинных эластомерных композиций на основе полиизопренового каучука и комбинации маслонаполненного бутадиен-стирольного и полибутадиенового каучуков. Выявлено, что частичная замена оксида цинка и стеариновой кислоты на цинкосодержащие технологические добавки не оказывает значительного влияния на основные физико-механические показатели резин на основе синтетических каучуков общего назначения. Определено, что при введении цинкосодержащих технологических добавок СЦС2 в комбинации с оксидом цинка во всех исследуемых соотношениях и СЦС3 в комбинации с оксидом цинка в соотношениях 4:1 и 3:1 несколько повышается (до 10,4%)устойчивость данных резин при действии температурно-силовых полей, что, вероятно, обусловлено более равномерным распределением полярных компонентов вулканизующей системы в неполярной эластомерной матрице, а также типом поперечных связей, образующихся в процессе вулканизации под действием поверхностно-активных цинкосодержащих добавок. Установлено, что введение в эластомерные композиции на основе СКМС-30 АРКМ-15 + СКД цинкосодержащих добавок в комбинации с оксидом цинка приводит к увеличению до 6,3% износостойкости резин, что может быть связано с меньшей дефектностью вулканизационной структуры данных резин, приводящей к уменьшению концентрации очагов напряжений в материале. Для резин на основе СКИ-3 показано сохранение прочности связи резины с текстильным кордом. Ключевые слова: каучук, эластомерная композиция, цинкосодержащая технологическая добавка, упруго-деформационные свойства, теплостойкость, прочность связи, износостойкость
The compatibility of SRI-3 polyisoprene rubber with plasticizing additives based on recycled petrochemical raw materials (DVCH, DVCH with modifying additive (MA) in the amount of 0.5; 1.0; 2.5; 5.0 and 10.0% mas.) in comparison with industrial petroleum oils (PO-6 and I-20). The compatibility of polymer with a plasticizer additive was evaluated by of experimental data using the equilibrium swelling method. As a result, the polimer-plasticizer interaction parameter (Huggins parameter) and the diffusion coefficient of plasticizing components in the polymer volume were determined. Analysis of the experimental data showed that the plasticizer component based on recycled petrochemical raw materials DVCH has better compatibility with the elastomer matrix SRI-3 compared to industrial oils PO-6 and I-20. Was established that the use of modifying additives in the amount of 0.5 and 1.0% mas. leads to an increase in the diffusion coefficient and a decrease in the Huggins parameter in comparison with DVCH in individual form It indicates their better compatibility with rubber SRI-3. Was shown that a further increase in the content of modifying additive (more than 1.0% mas.) in the volume of plasticizing component DVCH is impractical. This leads to a deterioration of the parameters, and, as a result, to a worse compatibility with the elastomer.
The influence of different types of silica, differing in quality characteristics, on the complex modulus of rubbers, their elastic modulus, loss modulus, and also on the tangent of angle of mechanical loss are investigated. Mineral fillers silica 1 and silica 2 are introduced at a dosage of 80.00 phr into filled elastomeric compositions based on combination of synthetic styrene-butadiene and polybutadiene rubbers, used for the manufacture of treads for passenger tires. The tests are carried out on a dynamic mechanical analyzer by cyclic compression of vulcanizates in the temperature range 20–70°С. It is established that vulcanizates with silica 2 are characterized by 8–56% lower value of the complex modulus. It is revealed that rubbers containing a silica 2, depending on temperature, have 13–36% lower values of the elastic modulus and 19–46% lower values of the loss modulus in comparison with samples filled with silica 2. It is determined that in the temperature range from 20 to 70°C vulcanizates with silica 2 are characterized by 7–12% lower values of the tangent of angle of mechanical loss. As a result of the study, it is established that it is the most expedient to introduce mineral filler silica 2 into the formulation of tread rubber compounds for passenger tires. This will make it possible to obtain vulcanizates with increased elasticity and adhesion to the road surface, as well as lower heat losses to the environment and fuel consumption.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.