В статті проведений аналіз існуючих на теперішній час літературних та патентних джерел, направлених на покращення параметрів якості поверхневих шарів деталей пар тертя. Метою роботи визначено підвищення якості та зносостійкості робочих поверхонь сталевих кілець торцевих імпульсних ущільнень, які можна використовувати в умовах радіаційного опромінювання, шляхом формування на робочих поверхнях кілець методом електро-іскрового легування квазібагатошарових покриттів, що об’єднують в собі змащувальні та механічні властивості. Авторами запропонований новий спосіб підвищення якості поверхонь стальних кілець торцевих імпульсних ущільнень, які працюють в умовах радіаційного опромінювання. Дослідження застосування нового способу проводили для сталей марок 12X18Н10Т, 30X13 і 40Х. Спосіб полягає в нанесенні методом електроіскрового легування на поверхню кільця торцевого імпульсного ущільненя покриття з міді при енергії розряду Wр = 0,04 Дж, а потім, на сформовану поверхню, наносять спеціальне технологічне насичуюче середовище у вигляді пастоподібної суміші, до складу якої входять – 80% карбіду вольфраму, 10% нікелю і 10% вазеліну, і проводять електроіскрове легування графітовим електродом при енергії розряду в межах Wр = 0,5–4,6 Дж. Легування міддю та графітовим електродом-інструментом відбувалось на установці з ручним вібратором «Елітрон-22А». З експериментальних зразків виготовлялися шліфи, які досліджували на оптичному мікроскопі «Неофот-2». За допомогою мікроскопа проводилася оцінка якості шару, його суцільності, товщини і будови зон підшару – дифузійної зони і зони термічного впливу. Також проводився дюрометричний аналіз на розподіл мікротвердості в поверхневому шарі і по глибині шліфа від поверхні. Застосування нового способу, дозволяє, формувати шари робочих поверхонь сталевих кілець торцевих імпульсних ущільнень підвищеної твердості товщиною залежно від марки сталі й енергії розряду при цементації методом електроіскрового легування від 30 до 115 мкм, мікротвердістю до 10350 МПа і суцільністю 100%. Шорсткість сформованого покриття знаходиться в межах Ra = 0,7–14,2 мкм. Подальше зниження шорсткості можливо за рахунок подальшої цементації методом електроіскрового легування, але з меншою енергією розряду, а також безабразивної ультразвукової фінішної обробки.
МОДЕРНИЗАцИЯ МЕХАНИЗМА УПРАВЛЕНИЯ ФИНАНСОВыМ ПОТЕНцИАЛОМ АГРОФОРМИРОВАНИй Обобщены теоретические подходы к пониманию сущности экономического механизма управления финансовым потенциалом. Обоснованы теоретические, методические и организационно-экономические аспекты его трансформации в контексте повышения уровня финансовой конкурентоспособности агроформирований и обеспечения позитивной динамики их экономического развития. Аргументировано авторскую позицию относительно интерпретации содержания экономического механизма управления финансовым потенциалом. Ключевые слова: агроформирование, экономический механизм, финансовый потенциал, финансовые ресурсы, финансовая конкурентоспособность, экономическое развитие.
This study focuses on the assessment of possible hypereutectoid steel carbide mesh crushing. It is used for tools production, including forming rolls of various diameters, with modification and cyclic heat treatment methods. For steel containing 1.79–1.83% C, we studied the effect of 0.35–1.15% Si on the possible crushing of the cementite mesh within crystallization by introducing modifiers Ti, V, N, as well as simultaneously modifying V with N and Ti with N. The obtained castings of Ø200 mm, 400 mm high were cut into discs, from which we made samples for tests on wear, determining mechanical properties, thermal resistance, and susceptibility to brittle fracture. The assessment was performed in the as-cast and after double and triple normalizing and annealing with drawback. With additional fans blowing, we changed the cooling rate from 25 °C/h to 100–150 °C/h. We performed the microstructure analyses using traditional metallographic, micro-X-ray spectral analyses, and also used the segmentation process based on 2D image markers. It was found that the as-cast modifying additives infusion is insufficient for carbide mesh crushing. It can be made by multi-stage normalizing with accelerated cool-down for products up to 600 mm in diameter to cycle temperatures above the steel transfer from a plastic to elastic state (above 450 °C).
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.