The results of experimental studies of the properties of composite materials based on poly(methylmetacrylate) (PMMA) matrices filled with electrolytic copper powder, having very high dendritic structure, are presented in this manuscript. Copper powder volume fractions used as filler in all prepared composites were varied in the range of 0.5 -8.8 %(v/v). The samples were prepared by hot molding injection at 180°C. Influence of particle size and morphology on the conductivity and percolation threshold and thermal properties of the composites were examined and characterization included: Scanning Electron Microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), Atomic Forces Microscopy (AFM). Composites have shown improvement of thermal characteristics in relation to pure polymer. Presence of three dimensional conductive pathways was confirmed. The obtained percolation threshold of 2.89 %(v/v) is about three times lower than the one stated in the literature, which is ascribed to different morphology of filler used in investigation.
This manuscript presents experimental studies of composite materials based on poly (L lactic acid) (PLLA) and poly (3-hydroxybutyrate) (PHB) matrices filled with electrolytic copper powder, having a very high dendritic structure. Volume fractions of the copper powder used as filler in all prepared composites were varied in the range 0.5-6.0 vol.%. Samples were prepared by hot moulding injection at 170 °C. Influence of particle size and morphology, as well as the influence of matrix type on conductivity and percolation threshold of the obtained composites were examined. Characterization included: electrical conductivity measurements using AC impedance spectroscopy (IS), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and Fourier-transform Infrared spectroscopy (FTIR). Presence of three-dimensional conductive pathways was confirmed. The obtained percolation thresholds of 2.83 vol.% for PLLA and 3.13 vol.% for PHB composites were measured, which is about three times lower than the ones stated in the literature for similar composites. This property is ascribed to different morphologies of the filler used in the present investigation.
Zastita Materijala 56 (4) 522 -526 (2015) Uloga i mehanizam dejstva inhibitora u rastvorima za nagrizanje čelika IZVOD Kiselo nagrizanje (bajcovanje) ima osnovni zadatak, bez obzira koja se kiselina upotrebljavala, da ukine korozione produkte sa predmeta prije nego što počne da nagriza osnovni materijal. Dejstvo kiseline na osnovni materijal izaziva gubitak metala i kiseline kao i nastajanje grešaka kod bajcovanja. Da bi se spriječilo ovo neželjeno sporedno dejstvo u rastvor za nagrizanje dodaje se inhibitor. U ovom radu testirali smo inhibitorsko dejstvo tri različita neorganska inhibitora u rastvoru HCl i H2SO4 i jednog organskog inhibitora u rastvoru H3PO4 u procesu bajcovanja cunderisanog čelika. Istraživanje je provedeno upotrebom gravimetrijske metode. Dobijeni rezultati ukazuju na zaštitnu vrijednost inhibitora preko 98% u svim testiranim koncentracijama HCl i H2SO4, dok je inhibitorsko dejstvo organskog inhibitora u rastvoru H3PO4 pri temperaturi od 60ºC izostalo.Ključne riječi: bajcovanje, inhibitor, čelik, zaštitna vrijednost inhibitora. UVODČelik je metal koji zbog svojih mehaničkih osobina i niske cjene koštanja ima široku primjenu u mnogim industrijama, zbog čega istraživanja vezana za inhibiciju korozije čelika imaju teorijski i praktičan značaj [1,2]. Upotreba inhibitora je jedna od najekonomičnijih metoda kojom se redukuje korozivno nagrizanje metala [3,4]. Pod inhibitorima korozije podrazumjevaju se supstance koje po uvođe-nju u korozionu sredinu, obično u malim količina-ma, mogu u velikoj mjeri da smanje brzinu elektrohemijske korozije metala i legura. Njihova primjena je veoma značajna u kiselim rastvorima za nagrizanje metala koji se koriste u pripremi površi-ne metala za galvansku i/ili hemijsku zaštitu ili lakiranje, prilikom čišćenja kamenca u sistemima gdje cirkuliše voda, destilacionim kolonama, parnim kotlovima, kontejnerima za vodu, uređajima za pretakanje itd. Posebnu pažnju, zbog značaja i vrijednosti objekta, potrebno je posvetiti u čišćenju kotlovnica. Čišćenje parnih kotlova kao i svako drugo industrijsko čišćenje, izvodi se kiselinama koje obavezno moraju biti inhibirane, tako da obezbjede optimalnu zaštitu materijala na postrojenjima. Rad je dostupan na sajtu: www.idk.org.rs/casopis Kiseline kao što su hlorovodonična, sumporna i fosforna kiseline, se često koriste za uklanjanje korozije [5,6]. Bez obzira koja se kiselina upotrebljava, zadatak rastvora za bajcovanje (nagrizanje), je da ukloni produkte korozije sa površine predmeta prije nego što počne nagrizati metal. Neželje-no sporedno dejstvo procesa bajcovanja je dejstvo kiseline na osnovni materijal, što izaziva gubitak i materijala i kiseline, kao i nastajanje grešaka na površini metala. Inhibitor u rastvoru za nagrazinje ima zadatak da spriječi neželjene procese, odnosno da bude nagrižen osnovni materijal. Kad je u pitanju željezo, sa pogodno odabranim inhibitorom, gubitak metala je za 90% niži nego kod bajcovanja sa čistom kiselinom. Na osnovu uštede koja nastaje zbog toga što nije rastvoren metal smanjuje se i potrošn...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.