No abstract

Semiconductor mode-locked lasers (MLLs) are promising frequency comb sources for dense wavelength-division-multiplexing (DWDM) data communications. Practical data communication requires a frequency-stable comb source in a temperature-varying environment and a minimum tone spacing of 25 GHz to support high-speed DWDM transmissions. To the best of our knowledge, however, to date, there have been no demonstrations of comb sources that simultaneously offer a high repetition rate and stable mode spacing over an ultrawide temperature range. Here, we report a frequency comb source based on a quantum dot (QD) MLL that generates a frequency comb with stable mode spacing over an ultrabroad temperature range of 20–120°C. The two-section passively mode-locked InAs QD MLL comb source produces an ultra-stable fundamental repetition rate of 25.5 GHz (corresponding to a 25.5 GHz spacing between adjacent tones in the frequency domain) with a variation of 0.07 GHz in the tone spacing over the tested temperature range. By keeping the saturable absorber reversely biased at − 2    V , stable mode-locking over the whole temperature range can be achieved by tuning the current of the gain section only, providing easy control of the device. At an elevated temperature of 100°C, the device shows a 6 dB comb bandwidth of 4.81 nm and 31 tones with > 36    dB optical signal-to-noise ratio. The corresponding relative intensity noise, averaged between 0.5 GHz and 10 GHz, is − 146    dBc / Hz . Our results show the viability of the InAs QD MLLs as ultra-stable, uncooled frequency comb sources for low-cost, large-bandwidth, and low-energy-consumption optical data communications.

We present dual DFB lasers each integrated with one heater developed in a generic foundry platform. The thermal effects are experimentally investigated and exhibited a continuous wavelength difference tuning of 0-12.33 nm.

Optical switching offers the potential to significantly scale the capacity of data center networks (DCN) with a simultaneous reduction in switching time and power consumption. Previous research has shown that end-to-end switching time, which is the sum of the switch configuration time and the clock and data recovery (CDR) locking time, should be kept within a few nanoseconds for high network throughput. This challenge of low switching time has motivated research into fast optical switches, ultra-fast clock and amplitude recovery techniques. Concurrently, the data rate between server-to-server and server-to-switch interconnect is increasing drastically from the current 100 Gb/s (4×25 Gb/s) to 400 Gb/s and beyond, motivating the use of high order formats such as 50-GBaud four-level pulse-amplitude modulation (PAM-4) for signalling. Since PAM-4 is more sensitive to noise and distortion, digital equalizers are generally needed to compensate for impairments such as transceiver frequency rolloff, dispersion and optical filtering, adding additional time for equalizer adaptation and power consumption that are undesired for fast optical switching systems. Here we propose and investigate an equalizer state caching technique that reduces equalizer adaptation time and computation power consumption for fast optical switching systems, underpinning optically-switched DCNs using high baud rate and impairment-sensitive formats. Through a proof-of-concept experiment, we study the performance of the proposed equalizer state caching scheme in a three-node optical switching system using 56 GBaud PAM-4. Our experimental results show that the proposed scheme can tolerate up to 0.8-nm (100-GHz) instantaneous wavelength change with an adaptation delay of only 0.36 ns. Practical considerations such as clock phase misalignment, temperature-induced wavelength drift, and equalizer precision are also studied.

In this paper, we investigate two categories of linear frequency-modulated chirp signals suitable for singlephotodiode based coherent light detection and ranging (Li-DAR) systems, namely, the frequency-modulated continuouswave (FMCW) single-sideband (SSB) signal and the amplitudemodulated double-sideband (DSB) signal, and compare their achievable receiver sensitivity performance. The DSB signal requires a simpler transmitter design, as it is real-valued and can be generated using a single-drive Mach-Zehnder modulator (MZM), while the SSB signal, which is frequency/phase modulated, requires an in-phase and quadrature modulator (IQM)based transmitter. A theoretical analysis of direct-detection (DD) beating interference (BI) especially the local oscillator (LO) beating with itself, known as LO-LO BI, is presented. Both Monte Carlo simulations and experimental demonstrations are carried out. Good agreement between simulations and experiments is achieved. In comparison with the SSB system, the DSB signalbased system is affected by laser phase noise-induced power fluctuation, and also suffers a significant sensitivity penalty due to nonlinear LO-LO BI. A spectral guard band for mitigating LO-LO BI is necessary for the DSB signal, achieved at the expense of requiring a larger electrical bandwidth. In system tests with a delay line of 385 m, the SSB signal outperforms the DSB signal with a 10 dB better receiver sensitivity in the case with a guard band, and 25 dB better sensitivity without a guard band.