At present, the clinical strategies for treating chronic wounds are limited, especially when it comes to pain relief and rapid wound healing. Therefore, there is an urgent need to develop...

Flexible electronics as an emerging technology has demonstrated potential for applications in various fields. With the advent of the Internet of Things era, countless flexible electronic systems need to be developed and deployed. However, materials and fabrication technologies are the key factors restricting the development and commercialization of flexible electronics. Here we report a simple, fast, and green flexible electronics preparation technology. The stencil printing method is adopted to pattern liquid metal on the thermoplastic polyurethane membrane prepared by electrospinning. Besides, with layer-by-layer assembly, flexible circuits, resistors, capacitors, inductors, and their composite devices can be prepared parametrically. Furthermore, these devices have good stretchability, air permeability, and stability, while they are multilayered and reconfigurable. As proof, this strategy is used to fabricate flexible displays, flexible sensors, and flexible filters. Finally, flexible electronic devices are also recycled and reconfigured.

Stem cells microencapsulated in hydrogel as stem cell-hydrogel constructs have wide applications in the burgeoning cell-based medicine. Due to their short shelf life at ambient temperature, long-term storage or banking of the constructs is essential to the "off-the-shelf" ready availability needed for their widespread applications. As a high-efficiency, easy-to-operate, low-toxicity, and low-cost method for long-term storage of the constructs, low-cryoprotectant (CPA) vitrification has attracted tremendous attention recently. However, we found many cells in the stem cell-alginate constructs (∼500 μm in diameter) could not attach to the substrate post low-CPA vitrification with ∼2 M penetrating CPAs. To address this problem, we introduced nanowarming via magnetic induction heating (MIH) of FeO nanoparticles to minimize recrystallization and devitrification during the warming step of the low-CPA vitrification procedure. Our results indicate that high-quality stem cell-alginate hydrogel constructs with an intact microstructure, high immediate cell survival (>80%), and greatly improved attachment efficiency (by nearly three times, 68% versus 24%) of the encapsulated cells could be obtained post-cryopreservation with nanowarming. Moreover, the cells encapsulated in the cell-hydrogel constructs post-cryopreservation maintained normal proliferation under 3D culture and retained intact biological function of multilineage differentiation. This novel low-CPA vitrification approach for cell cryopreservation enabled by the combined use of alginate hydrogel microencapsulation and FeO nanoparticles-mediated nanowarming may be valuable in facilitating the widespread application of stem cells in the clinic.

Two-dimensional (2D) graphene oxide (GO) and molybdenum disulfide (MoS2) nanosheets (NSs) have been widely used as photothermal agents and as potential carriers of antitumor drugs. Their spatial thermal effects have been extensively explored for use at physiological and hyperthermic temperatures (37 to 46 °C). Furthermore, the modulation of the spatial thermal distributions with these NSs may have even more profound applications in the microstructural control of biomaterials at cryogenic temperatures (-196 to 37 °C). These applications include bioinspired microfabrication via freezing, food and drug freeze-drying, and biomaterial cryopreservation. However, such thermal effects of NSs and their applications at cryogenic temperatures had never been fully explored. Therefore, in this study, we have utilized the near-infrared laser induced photothermal effects of GO and MoS2 NSs to suppress the ice nucleation and ice crystal growth during warming of the biosamples. Using this approach, biological cells subjected to fast cooling to a deeply frozen state (-196 °C) were successfully recovered with high survival rates and full biological functionality. Thus, we provide a NS based effective approach to control the crystallization behaviors of water during warming at cryogenic temperatures, as NSs may have wide applications in both materials science and bioengineering.

Accurate characterization of the cell membrane transport properties of human oocytes is of great significance to reproductive pharmacology, fertility preservation, and assisted reproduction. However, the commonly used manual method for quantifying the transport properties is associated with uncontrolled operator-to-operator and run-to-run variability. Here, we report a novel sandwich structured microfluidic device that can be readily fabricated for characterizing oocyte membrane transport properties. Owing to its capacity of excellent control of both solution replacement and temperature in the microchannel, the temperature-dependent permeability of oocyte membrane can be precisely characterized. Furthermore, the fertilization and developmental competence analysis post perfusion indicate that our approach does not compromise the physiological function of in-vitro matured human oocytes. Collectively, we present the development of a novel sandwich structured microfluidic device based approach that allows for on-chip characterization of the transport properties of human oocytes under innocuous osmotic shock or injury to the cells.