Metal organic frameworks (MOFs), with their crystalline, porous structures, can be synthesized to incorporate a wide range of catalytically active metals in tailored surroundings. These materials have potential as catalysts for conversion of light alkanes, feedstocks available in large quantities from shale gas that are changing the economics of manufacturing commodity chemicals. Mononuclear high-spin (S = 2) Fe(II) sites situated in the nodes of the MOF MIL-100(Fe) convert propane via dehydrogenation, hydroxylation, and overoxidation pathways in reactions with the atomic oxidant N 2 O. Pair distribution function analysis, N 2 adsorption isotherms, X-ray diffraction patterns, and infrared and Raman spectra confirm the single-phase crystallinity and stability of MIL-100(Fe) under reaction conditions (523 K in vacuo, 378−408 K C 3 H 8 + N 2 O). Density functional theory (DFT) calculations illustrate a reaction mechanism for the formation of 2-propanol, propylene, and 1-propanol involving the oxidation of Fe(II) to Fe(III) via a high-spin Fe(IV)O intermediate. The speciation of Fe(II) and Fe(III) in the nodes and their dynamic interchange was characterized by in situ X-ray absorption spectroscopy and ex situ Mossbauer spectroscopy. The catalytic relevance of Fe(II) sites and the number of such sites were determined using in situ chemical titrations with NO. N 2 and C 3 H 6 production rates were found to be first-order in N 2 O partial pressure and zero-order in C 3 H 8 partial pressure, consistent with DFT calculations that predict the reaction of Fe(II) with N 2 O to be rate determining. DFT calculations using a broken symmetry method show that Fe-trimer nodes affecting reaction contain antiferromagnetically coupled iron species, and highlight the importance of stabilizing high-spin (S = 2) Fe(II) species for effecting alkane oxidation at low temperatures (<408 K).

No abstract

Iodine detection is crucial for nuclear waste clean-up and first responder activities. For ease of use and durability of response, robust active materials that enable the direct electrical detection of I2 are needed. Herein, a large reversible electrical response is demonstrated as I2 is controllably and repeatedly adsorbed and desorbed from a series of metal–organic frameworks (MOFs) MFM-300(X), each possessing a different metal center (X = Al, Fe, In, or Sc) bridged by biphenyl-3,3′,5,5′-tetracarboxylate linkers. Impedance spectroscopy is used to evaluate how the different metal centers influence the electrical response upon cycling of I2 gas, ranging from 10× to 106× decrease in resistance upon I2 adsorption in air. This large variation in electrical response is attributed not only to the differing structural characteristics of the MOFs but also to the differing MOF morphologies and how this influences the degree of reversibility of I2 adsorption. Interestingly, MFM-300(Al) and MFM-300(In) displayed the largest changes in resistance (up to 106×) yet lost much of their adsorption capacity after five I2 adsorption cycles in air. On the other hand, MFM-300(Fe) and MFM-300(Sc) revealed more moderate changes in resistance (10–100×), maintaining most of their original adsorption capacity after five cycles. This work demonstrates how changes in MOFs can profoundly affect the magnitude and reversibility of the electrical response of sensor materials. Tuning both the intrinsic (resistivity and adsorption capacity) and extrinsic (surface area and particle morphology) properties is necessary to develop highly reversible, large signal-generating MOF materials for direct electrical readout for I2 sensing.

ParagraphConducting organic materials, such as doped organic polymers, 1 molecular conductors, 2, 3 and emerging coordination polymers, 4 underpin technologies ranging from displays to flexible electronics. 5 Realizing high electrical conductivity in traditionally insulating organic materials necessitates tuning their electronic structure through chemical doping. 6 Furthermore, even materials that are intrinsically conductive, such as single-component molecular conductors, 7,8 require crystallinity for metallic behavior. However, commercial conducting polymers are often purposefully amorphous to aid in durability and processability. 9,10 Using molecular design to engender high conductivity in undoped amorphous materials would enable tunable and robust conductivity in many applications, but there are no intrinsically conducting organic materials which maintain high conductivity when disordered. Here we show that the completely amorphous coordination polymer Ni tetrathiafulvalene tetrathiolate (NiTTFtt) displays intrinsic metallic conductivity. Despite its disordered structure, NiTTFtt exhibits remarkably high electronic conductivity (1280 S/cm) and intrinsically glassy metallic behavior. Analysis with advanced theory shows that these properties are enabled by strong molecular overlap and correlation that are robust to structural perturbations. This unusual set of structural and electronic features results in remarkably stable organic conductivity which is maintained in air for weeks and at temperatures up to 140 °C. Our results demonstrate that molecular design can enable metallic conductivity even in heavily disordered materials. This both raises fundamental questions about how band-like transport can exist in the absence of periodic structure as well as suggests exciting new applications for these materials.

Organometallic iridium catalysts can be used in conjunction with bispinacolatodiboron (B 2 Pin 2 ) to effect the borylation of a variety of substrates such as arenes, alkanes, heteroarenes, and oxygenates. Recently, efforts have also focused on integrating these catalysts into porous supports, such as metal−organic frameworks (MOFs). While the mechanism of homogeneous borylation systems has been thoroughly investigated experimentally and computationally, analogous studies in MOF-supported iridium catalysts have not been conducted. Herein, we report the mechanistic investigation of a phenanthroline-iridium catalyst immobilized in the organic linker of Universitetet i Oslo (UiO)-67 (Zr 6 O 4 (OH) 4 (BPDC) 4 (PhenDC) 2 , BPDC = biphenyl-4,4′-dicarboxylate, PhenDC = 1,10-phenanthroline-4,4′-dicarboxylate). By using benzene as a model substrate, variable time normalization analysis (VTNA) of the kinetic data suggested a rate law consistent with zero-order in B 2 Pin 2 , and first-order in arene. A primary kinetic isotope effect (KIE) in the time course of benzene-d 6 borylation also provided complementary information about the role of the arene in the rate-determining step of the reaction. Characterization by techniques such as X-ray absorption spectroscopy (XAS) confirmed the presence of Ir(III), while pair distribution function (PDF) analysis suggested structures containing an Ir−Cl bond, further substantiated by X-ray photoelectron spectroscopy (XPS). Analysis of postcatalysis materials by inductively coupled plasma− optical emission spectroscopy (ICP-OES) revealed low boron accumulation, which may indicate an absence of boron in the resting state of the catalyst. Finally, in comparing borylation of benzene and toluene, a slight selectivity for benzene is observed, which is similar to the analogous homogeneous reaction, indicating the influence of substrate sterics on reactivity.