Thermally conductive polymer composites offer new possibilities for replacing metal parts in several applications, including power electronics, electric motors and generators, heat exchangers etc., thanks to the polymer advantages such as light weight, corrosion resistance and ease of processing. Current interest to improve the thermal conductivity of polymers is focused on the selective addition of nanofillers with high thermal conductivity. Unusually high thermal conductivity makes carbon nanotube (CNT) the best promising candidate material for thermally conductive composites. However, the thermal conductivities of polymer/CNT nanocomposites are relatively low compared with expectations from the intrinsic thermal conductivity of CNTs. The 2 challenge primarily comes from the large interfacial thermal resistance between the CNT and the surrounding polymer matrix, which hinders the transfer of phonon dominating heat conduction in polymer and CNT. This article reviews the status of worldwide research in the thermal conductivity of CNTs and their polymer nanocomposites. The dependence of thermal conductivity of nanotubes on the atomic structure, the tube size, the morphology, the defect and the purification is reviewed. The roles of particle/polymer and particle/particle interfaces on the thermal conductivity of polymer/CNT nanocomposites are discussed in detail, as well as the relationship between the thermal conductivity and the micro-and nano-structure of the composites.

No abstract

No abstract

High seed vigor is important for agricultural production due to the associated potential for increased growth and productivity. However, a better understanding of the underlying molecular mechanisms is required because the genetic basis for seed vigor remains unknown. We used single-nucleotide polymorphism (SNP) markers to map quantitative trait loci (QTLs) for four seed vigor traits in two connected recombinant inbred line (RIL) maize populations under four treatment conditions during seed germination. Sixty-five QTLs distributed between the two populations were identified and a meta-analysis was used to integrate genetic maps. Sixty-one initially identified QTLs were integrated into 18 meta-QTLs (mQTLs). Initial QTLs with contribution to phenotypic variation values of R2>10% were integrated into mQTLs. Twenty-three candidate genes for association with seed vigor traits coincided with 13 mQTLs. The candidate genes had functions in the glycolytic pathway and in protein metabolism. QTLs with major effects (R2>10%) were identified under at least one treatment condition for mQTL2, mQTL3-2, and mQTL3-4. Candidate genes included a calcium-dependent protein kinase gene (302810918) involved in signal transduction that mapped in the mQTL3-2 interval associated with germination energy (GE) and germination percentage (GP), and an hsp20/alpha crystallin family protein gene (At5g51440) that mapped in the mQTL3-4 interval associated with GE and GP. Two initial QTLs with a major effect under at least two treatment conditions were identified for mQTL5-2. A cucumisin-like Ser protease gene (At5g67360) mapped in the mQTL5-2 interval associated with GP. The chromosome regions for mQTL2, mQTL3-2, mQTL3-4, and mQTL5-2 may be hot spots for QTLs related to seed vigor traits. The mQTLs and candidate genes identified in this study provide valuable information for the identification of additional quantitative trait genes.

Maize architecture is a major contributing factor to their high level of productivity. Maize varieties with an erect-leaf-angle (LA) phenotype, which increases light harvesting for photosynthesis and grain-filling, have elevated grain yields. Although a large body of information is available on the map positions of quantitative trait loci (QTL) for LA, little is known about the molecular mechanism of these QTL. In this study, the ZmCLA4 gene, which is responsible for the qLA4-1 QTL associated with LA, was identified and isolated by fine mapping and positional cloning. The ZmCLA4 gene is an orthologue of LAZY1 in rice and Arabidopsis. Sequence analysis revealed two SNPs and two indel sites in ZmCLA4 between the D132 and D132-NIL inbred maize lines. Association analysis showed that C/T/mutation667 and CA/indel965 were strongly associated with LA. Subcellular localization verified the functions of a predicted transmembrane domain and a nuclear localization signal in ZmCLA4. Transgenic maize plants with a down-regulated ZmCLA4 RNAi construct and transgenic rice plants over-expressing ZmCLA4 confirmed that the ZmCLA4 gene located in the qLA4 QTL regulated LA. The allelic variants of ZmCLA4 in the D132 and D132-NIL lines exhibited significant differences in leaf angle. ZmCLA4 transcript accumulation was higher in D132-NIL than in D132 during all the developmental stages and was negatively correlated with LA. The gravitropic response was increased and cell shape and number at the leaf and stem junctions were altered in D132-NIL relative to D132. These findings suggest that ZmCLA4 plays a negative role in the control of maize LA through the alteration of mRNA accumulation, leading to altered shoot gravitropism and cell development. The cloning of the gene responsible for the qLA4-1 QTL provides information on the molecular mechanisms of LA in maize and an opportunity for the improvement of plant architecture with regard to LA through maize breeding.

As one of important biomaterials for localized drug delivery system, chitosan hydrogel still suffer several challenges, including poor mechanical properties, passive drug release behavior and lack of remote stimuli response. To address these challenges, a facile in situ hybridization method was reported for fabricate tough magnetic chitosan hydrogel (MCH), which remotely switched drug release from passive release to pulsatile release under a low frequency alternating magnetic field (LAMF). The in situ hybridization method avoided the aggregation of magnetic nanoparticles (MNPs) in hydrogel, which simultaneously brings 416% and 265% increase in strength and elastic modulus, respectively. The mechanical property enhancement was contributed by the physical crosslinking of in situ synthesized MNPs. When a LAMF with 15 min ON-15 min OFF cycles was applied to MCH, the fraction release showed zigzag shape and pulsatile release behavior with quick response. The cumulative release and fraction release of drug from MCH were improved by 67.2% and 31.9%, respectively. MTT results and cell morphology indicated that the MCH have excellent biocompatibility and no acute adverse effect on MG-63 cells. The developed tough MCH system holds great potential for applications in smart drug release system with noninvasive characteristics and magnetic field stimulated drug release behavior.

No abstract

There is an increasing interest in polymer layered silicate nanocomposites, due to the enhanced properties of these systems. An additional layered system is the graphite oxide system and this has been studied as polyacrylate ester nanocomposites. These have been characterized using X‐ray diffraction and a variety of fire tests. There is a significant change in the oxygen index for nanocomposites which is absent for microcomposites, unlike the situation for the clay‐based systems. X‐ray photoelectron spectroscopy showed that the surface was covered with a graphite oxide‐like material at high temperatures for the nanocomposites, suggesting that this nano‐dimensional material operates as a barrier, exactly as proposed for polymer‐clay systems. Copyright © 2006 John Wiley & Sons, Ltd.