Over the years, the field of bioprinting has attracted attention for its highly automated 16 fabrication system that enables the precise patterning of living cells and biomaterials at pre-17 defined positions for enhanced cell-matrix and cell-cell interactions. Notably, vat polymerization 18 (VP)-based bioprinting is an emerging bioprinting technique for various tissue engineering 19 applications due to its high fabrication accuracy. Particularly, different photo-initiators (PIs) are 20 utilized during the bioprinting process to facilitate the crosslinking mechanism for fabrication of 21 high-resolution complex tissue constructs. The advancements in VP-based printing have led to a 22 paradigm shift in fabrication of tissue constructs from cell-seeding of tissue scaffolds (non-23 biocompatible fabrication process) to direct bioprinting of cell-laden tissue constructs 24 (biocompatible fabrication process). This paper, presenting a first-time comprehensive review of 25 the VP-based bioprinting process, provides an in-depth analysis and comparison of the various 26 biocompatible PIs and highlights the important considerations and bioprinting requirements. This 27 review paper reports a detailed analysis of its printing process and the influence of light-based 28 curing modality and PIs on living cells. Lastly, this review also highlights the significance of VP-29 based bioprinting, the regulatory challenges and presents future directions to transform the VP-30 Page 1 of 47 AUTHOR SUBMITTED MANUSCRIPT -BF-102156.R2based printing technology into imperative tools in the field of tissue engineering and regenerative 31 medicine. The readers will be informed on the current limitations and achievements of the VP-32 based bioprinting techniques. Notably, the readers will realize the importance and value of 33 highly-automated platforms for tissue engineering applications and be able to develop objective 34 viewpoints towards this field.

No abstract

The nucleoprotein (NP) of the influenza virus exists as trimers, and its tail-loop binding pocket has been suggested as a potential target for antiinfluenza therapeutics. The possibility of NP as a drug target was validated by the recent reports that nucleozin and its analogs can inhibit viral replication by inducing aggregation of NP trimers. However, these inhibitors were identified by random screening, and the binding site and inhibition mechanism are unclear. We report a rational approach to target influenza virus with a new mechanism-disruption of NP-NP interaction. Consistent with recent work, E339A, R416A, and deletion mutant Δ402-428 were unable to support viral replication in the absence of WT NP. However, only E339A and R416A could form hetero complex with WT NP, but the complex was unable to bind the RNA polymerase, leading to inhibition of viral replication. These results demonstrate the importance of the E339…R416 salt bridge in viral survival and establish the salt bridge as a sensitive antiinfluenza target. To provide further support, we showed that peptides encompassing R416 can disrupt NP-NP interaction and inhibit viral replication. Finally we performed virtual screening to target E339…R416, and some small molecules identified were shown to disrupt the formation of NP trimers and inhibit replication of WT and nucleozinresistant strains. This work provides a new approach to design antiinfluenza drugs.T he RNA-dependent RNA polymerase (RDRP) of the influenza A virus is composed of polymerase basic protein 1 (PB1), basic protein 2 (PB2), and acidic protein (PA) (1). The function of RDRP for viral replication requires association with the nucleoprotein (NP) (2) to form the ribonucleoprotein (RNP) complex. Only low resolution structures of the RNP complex are available from cryo-EM studies (2-9), whereas high resolution structures have been reported for some individual components or fragments (10-12). Crystal structures of NP indicate that it exists in trimers (13,14), with the tail-loop (residues 402-428) region playing an important role in the trimerization (Fig. 1A). Based on the structural information, it was suggested that the tail-loop binding pocket could be a target for antiinfluenza therapeutics (13,14).Disruption of the NP-NP interaction as a strategy for designing antiinfluenza drugs has been further reported. Many mutants of NP, including some tail-loop mutants, lose the ability to support the RDRP activity in reconstitution experiments (2,(15)(16)(17)(18). In addition, some of the mutants are shown to exist in monomers instead of trimers. These results support the importance of NP in the RDRP activity and viral replication, and the possibility of NP as a drug target. However, it remains to be shown that molecules capable of disrupting the NP-NP interaction would inhibit viral replication.Recently Kao et al. (19) and our group (20) reported the use of high throughput screening to identify nucleozin and its analogs as inhibitors that halt viral replication by binding to NP and causing it...

No abstract

The present study provides a solvent-free processing method for establishing the ideal porous 3-dimension (3D) scaffold filled with different ratios of calcium silicate-based (CS) powder and polycaprolactone (PCL) for 3D bone substitute application. Characterization of hybrid scaffolds developed underwent assessments for physicochemical properties and biodegradation. Adhesion and growth of human Wharton's Jelly mesenchymal stem cells (WJMSCs) on the CS/PCL blended scaffold were investigated in vitro. Cell attachment and morphology were examined by scanning electron microscope (SEM) and confocal microscope observations. Colorimetric assay was tested for assessing cell metabolic activity. In addition, RT-qPCR was also performed for the osteogenic-related and angiogenesis-related gene expression. As a result, the hydrophilicity of the scaffolds was further significantly improved after we additive CS into PCL, as well as the compressive strength up to 5.8 MPa. SEM showed that a great amount of precipitated bone-like apatite formed on the scaffold surface after immersed in the simulated body fluid. The 3D-printed scaffolds were found to enhance cell adhesion, proliferation and differentiation. Additionally, results of osteogenesis and angiogenesis proteins were expressed obviously greater in the response of WJMSCs. These results indicate the CS/PCL composite exhibited a favorable bioactivity and osteoconductive properties that could be served as a promising biomaterial for bone tissue engineering scaffolds.

Diseases in articular cartilages have affected millions of people globally. Although the biochemical and cellular composition of articular cartilages is relatively simple, there is a limitation in the self-repair ability of the cartilage. Therefore, developing strategies for cartilage repair is very important. Here, we report on a new liquid resin preparation process of water-based polyurethane based photosensitive materials with hyaluronic acid with application of the materials for 3D printed customized cartilage scaffolds. The scaffold has high cytocompatibility and is one that closely mimics the mechanical properties of articular cartilages. It is suitable for culturing human Wharton’s jelly mesenchymal stem cells (hWJMSCs) and the cells in this case showed an excellent chondrogenic differentiation capacity. We consider that the 3D printing hybrid scaffolds may have potential in customized tissue engineering and also facilitate the development of cartilage tissue engineering.

No abstract

The purpose of 4D printing is to embed a product design into a deformable smart material using a traditional 3D printer. The 3D printed object can be assembled or transformed into intended designs by applying certain conditions or forms of stimulation such as temperature, pressure, humidity, pH, wind, or light. Simply put, 4D printing is a continuum of 3D printing technology that is now able to print objects which change over time. In previous studies, many smart materials were shown to have 4D printing characteristics. In this paper, we specifically review the current application, respective activation methods, characteristics, and future prospects of various polymeric materials in 4D printing, which are expected to contribute to the development of 4D printing polymeric materials and technology.