This study analyzes the fundamental principles and characteristics of the microcellular foaming process (MCP) to minimize warpage in glass fiber reinforced polymer (GFRP), which is typically worse than that of a solid polymer. In order to confirm the tendency for warpage and the improvement of this phenomenon according to the glass fiber content (GFC), two factors associated with the reduction of the shrinkage difference and the non-directionalized fiber orientation were set as variables. The shrinkage was measured in the flow direction and transverse direction, and it was confirmed that the shrinkage difference between these two directions is the cause of warpage of GFRP specimens. In addition, by applying the MCP to injection molding, it was confirmed that warpage was improved by reducing the shrinkage difference. To further confirm these results, the effects of cell formation on shrinkage and fiber orientation were investigated using scanning electron microscopy, micro-CT observation, and cell morphology analysis. The micro-CT observations revealed that the fiber orientation was non-directional for the MCP. Moreover, it was determined that the mechanical and thermal properties were improved, based on measurements of the impact strength, tensile strength, flexural strength, and deflection temperature for the MCP.
Shrinkage and warpage of injection-molded parts can be minimized by applying microcellular foaming technology to the injection molding process. However, unlike the conventional injection molding process, the optimal conditions of the microcellular foam injection molding process are elusive because of core differences such as gas injection. Therefore, this study aims to derive process conditions to minimize the shrinkage and warpage of microcellular foam injection-molded parts made of glass fiber reinforced polyamide 6 (PA6/GF). Process factors and levels were first determined, with experiments planned accordingly. We simulated designed experiments using injection molding analysis software, and the results were analyzed using the Taguchi method, analysis of variance (ANOVA), and response surface methodology (RSM), with the ANOVA analysis being ultimately demonstrating the influence of the factors. We derived and verified the optimal combination of process factors and levels for minimizing both shrinkage and warpage using the Taguchi method and RSM. In addition, the mechanical properties and cell morphology of PA6/GF, which change with microcellular foam injection molding, were confirmed.
The shrinkage of reinforced polymer composites in injection molding varies, depending on the properties of the reinforcing agent. Therefore, the study of optimal reinforcement conditions, to minimize shrinkage when talc and glass fibers (GF) (which are commonly used as reinforcements) are incorporated into polypropylene (PP), is required. In this study, we investigated the effect of reinforcement factors, such as reinforcement type, reinforcement content, and reinforcement particle size, on the shrinkage, and optimized these factors to minimize the shrinkage of the PP composites. We measured the shrinkage of injection-molded samples, and, based on the measured values, the optimal conditions were obtained through analysis of variance (ANOVA), the Taguchi method, and regression analysis. It was found that reinforcement type had the largest influence on shrinkage among the three factors, followed by reinforcement content. In contrast, the reinforcement size was not significant, compared to the other two factors. If the reinforcement size was set as an uncontrollable factor, the optimum condition for minimizing directional shrinkage was the incorporation of 20 wt % GF and that for differential shrinkage was the incorporation of 20 wt % talc. In addition, a shrinkage prediction method was proposed, in which two reinforcing agents were incorporated into PP, for the optimization of various dependent variables. The results of this study are expected to provide answers about which reinforcement agent should be selected and incorporated to minimize the shrinkage of PP composites.
As the consumption of coffee increases worldwide, the amount of spent coffee grounds (SCG) is gradually increasing every year. Some of these grounds are recycled for composting, but most are discarded, which causes widespread financial and social costs. We developed a bio-based plastic pellet by blending polypropylene (PP) with waste biomass SCG to convert it into a sustainable, recyclable eco-friendly material. It was confirmed that extrusion compounding for SCG/PP composite pellets and injection molding with good formability are possible. To evaluate the formability of the composite pellets, American Society for Testing and Materials (ASTM) test specimens were prepared for evaluating mechanical properties by injection molding. As a result of the measurement of the test samples, the mechanical properties of SCG/PP composite pellets were generally lowered as the SCG content increased. However, the impact strength of SCG/PP composite based on the HOMO-PP matrix improved as the SCG content increased. In addition, Young’s modulus of SCG/PP increased as the SCG content increased. In the future, this study will be applied to manufacture of products that requires non-toxic products, such as disposable products and food containers, realizing commercialization of eco-friendly products and thereby replacing finite petroleum resources and practicing resource circulation and environmental protection.
In this work, a high-magnification extrusion-foaming technique for biomass-based biodegradable composite materials using water vaporization was examined. Starch was selected as the biomass and polylactic acid was selected as a biodegradable matrix resin. No additional plasticizer or additives were used in this extrusion-foaming process. The foaming ratio was deduced according to the conditions of the extrusion-foaming process to confirm the forming characteristics of the foaming materials. Scanning electron microscopy was performed to examine the morphology of the composite foam. To investigate the potential of the foam cushion as an ecofriendly packing material, we conducted experiments on its static compression and dynamic cushioning properties and examined whether its biodegradability could be controlled by varying the mixing ratio of the materials. Thus, we developed a water-foaming process that is ecofriendly and whose products can be recycled as compost after use.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.