Property by design is one appealing idea in material synthesis but hard to achieve in practice. A recent successful example is the demonstration of van der Waals (vdW) heterostructures, 1-3 in which atomic layers are stacked on each other and different ingredients can be combined beyond symmetry and lattice matching. This concept, usually described as a nanoscale Lego blocks, allows to build sophisticated structures layer by layer. However, this concept has been so far limited in two dimensional (2D) materials. Here we show a class of new material where different layers are coaxially (instead of planarly) stacked. As the structure is in one dimensional (1D) form, we name it "1D vdW heterostructures". We demonstrate a 5 nm diameter nanotube consisting of three different materials: an inner conductive carbon nanotube (CNT), a middle insulating hexagonal boron nitride nanotube

No abstract

of the 2D structures has approached its limit (< 90%) due to which the energy loss via reflection (2-5%) and thermal radiation heat loss (8-12%) occurs in all the 2D structures.One of the effective strategies for further improving the vapor-generation efficiency is to decrease the surface temperature of the absorber by increasing the surface area within a given projection area. [22] Some unprecedented vapor-generation rates have been reported in various 3D generators, which are all beyond the input solar energy limit. [23][24][25] Here, we have found that bamboos, as a natural hierarchical cellular material, can be excellent 3D solar vapor-generation devices due to their unique structural features. By a simple carbonization progress, the bamboos maintain remarkable mechanical property. Meanwhile, the carbonized bamboo-based evaporator possesses the following advantages: 1) natural hydrophilicity; 2) numerous aligned microchannels acting as highways for rapid water transport; 3) high light absorptance in a broad spectral range; 4) reduced thermal radiation heat loss; 5) lower average temperature than environment; 6) reduced vaporization enthalpy of water confined in the bamboo mesh; 7) remarkable mechanical properties; 8) ability of salt self-cleaning; 9) good scalability and low cost. As a result, a floating carbonized bamboo sample can evaporate water with an extremely high vapor-generation rate of 3.13 kg m −2 h −1 under 1 sun illumination. It also shows superior reusability and stability for solar vapor generation, without any performance degradation after cycling 360 h. The carbonized bamboo shows favorable overall performance compared with other reported solar vapor generators and has attractive applications in desalination as well asindustrial and domestic wastewater abatement. All of these features are elucidated below in detail.Bamboo is the fastest-growing and highest-yielding hierarchical cellular material on the Earth. A typical bamboo reaches maturity within months and ultimate mechanical properties within few years, making it one of the most renewable resources. [26] Figure 1a-c shows the illustration of the design concept for a bamboo-based solar vapor-generation device. Bamboo tubes with desired height were cut from the natural bamboo and were carbonized to make it dark. The carbonized Given the global challenges of water scarcity, solar-driven vapor generation has become a renewed topic as an energy-efficient way for clean water production. Here, it is revealed that bamboo, as a natural hierarchical cellular material, can be an excellent 3D solar vapor-generation device by a simple carbonization progress. A floating carbonized bamboo sample evaporates water with an extremely high vapor-generation rate of 3.13 kg m −2 h −1 under 1 sun illumination. The high evaporation rate is achieved by the unique natural structure of bamboos. The inner wall of bamboo recovers the diffuse light energy and the thermal radiation heat loss from the 3D bamboo bottom, and the outer wall captures energy from the warmer...

Flexible supercapacitors, which can sustain large deformations while maintaining normal functions and reliability, are playing an increasingly important role in portable electronics. Here we report the preparation of a three-dimensional α-Fe 2 O 3 /carbon nanotube (CNT@Fe 2 O 3 ) sponge electrode with a porous hierarchical structure, consisting of a compressible, conductive CNT network, coated with a layer of Fe 2 O 3 nanohorns. The specific capacitance of these hybrid sponges has been significantly improved to above 300 F/g, while the equivalent series resistance remains at about 1.5 Ω. The highly deformed CNT@Fe 2 O 3 sponge retains more than 90 % of the original specific capacitance under a compressive strain of 70% (corresponding to a volume reduction of 70%). The hybrid sponge still works stably and sustains similar specific capacitance as initial value even after 1000 compression cycles at a strain of 50%. The outstanding properties of this hybrid sponge make it a highly promising candidate for flexible energy devices.

No abstract

Nature-motivated pressure sensors have been greatly important components integrated into flexible electronics and applied in artificial intelligence. Here, we report a high sensitivity, ultrathin, and transparent pressure sensor based on wrinkled graphene prepared by a facile liquid-phase shrink method. Two pieces of wrinkled graphene are face to face assembled into a pressure sensor, in which a porous anodic aluminum oxide (AAO) membrane with the thickness of only 200 nm was used to insulate the two layers of graphene. The pressure sensor exhibits ultrahigh operating sensitivity (6.92 kPa), resulting from the insulation in its inactive state and conduction under compression. Formation of current pathways is attributed to the contact of graphene wrinkles through the pores of AAO membrane. In addition, the pressure sensor is also an on/off and energy saving device, due to the complete isolation between the two graphene layers when the sensor is not subjected to any pressure. We believe that our high-performance pressure sensor is an ideal candidate for integration in flexible electronics, but also paves the way for other 2D materials to be involved in the fabrication of pressure sensors.

Please refer to published version for the most recent bibliographic citation information. If a published version is known of, the repository item page linked to above, will contain details on accessing it.

A continuous mesoporous iron oxide nanofilm was directly formed on graphene nanosheets through the in situ thermal decomposition of Fe(NO 3 ) 3 ?9H 2 O and was anchored tightly on the graphene surface. The lithiation-induced strain was naturally accommodated, owing to the constraint effect of graphene and the mesoporous structure. Hence, the pulverization of the iron oxide nanofilm was effectively prevented.3 Electronic supplementary information (ESI) available: experimental details, XRD patterns, additional SEM and TEM images, SEM mapping, N 2 adsorptiondesorption analysis, FT-IR spectrum, XPS spectrum and additional electrochemical data. See