We report on a systematic study of solvent and polymer matrix effects on the phase segregation behavior of 6,13-bis(triisopropylsilylethynyl) pentacene (TIPS-pentacene) blends incorporated into two different amorphous polymer matrices, poly (a-methyl styrene) and poly (triarylamine), and using two solvents, chlorobenzene and tetralin. Optical microscopy, X-ray diffraction analyses, and optical absorption measurements are used to evaluate the film morphology, crystallinity, and optical density, respectively. These analyses are correlated with the extent of vertical segregation of TIPS-pentacene, as observed for the blended films by depth-profile XPS analyses. The microstructure and vertical phase segregation of TIPS-pentacene in blend films are found to be strongly influenced by the choice of solvent. Tetralin, a solvent with a high boiling temperature, was found to be more desirable for achieving distinct phase segregation/crystallization of TIPS-pentacene in blend films and best performance in OFETs with a dual-gate geometry. The electrical properties of top and bottom channels were consistent with the morphological characterization and OFETs processed from tetralin showed higher mobility values than those from chlorobenzene. Further modification of the annealing conditions in the TIPS-pentacene/PTAA/tetralin ternary system led to top-gate OFETs with mobility values up to 2.82 cm 2 /Vs.

No abstract

As the needs for low-cost rapidly-produced microfluidics are growing with the trend of Lab-on-a-Chip and distributed healthcare, the fully inkjet-printing of microfluidics can be a solution to it with numerous potential electrical and sensing applications. Inkjet-printing is an additive manufacturing technique featuring no material waste and a low equipment cost. Moreover, similar to other additive manufacturing techniques, inkjet-printing is easy to learn and has a high fabrication speed, while it offers generally a great planar resolution down to below 20 µm and enables flexible designs due to its inherent thin film deposition capabilities. Due to the thin film feature, the printed objects also usually obtain a high vertical resolution (such as 4.6 µm). This paper introduces a low-cost rapid three-dimensional fabrication process of microfluidics, that relies entirely on an inkjet-printer based single platform and can be implemented directly on top of virtually any substrates.

No abstract

Growth of Si1−xSnx alloys on Ge1−ySny-buffered Si(100) was achieved via reactions of SnD4 and SiH3SiH2SiH3 at 275°C. Kinetic studies indicate that unprecedented low growth temperatures are made possible by the highly reactive SiH2 groups. The authors obtain supersaturated metastable compositions (y∼25%) near the indirect to direct band gap crossover predicted by first principles simulations. Extensive characterizations of composition, structure, and morphology show that the SiSn∕GeSn films grow lattice matched via a “compositional pinning” mechanism. The initial Raman observations of Si–Sn bond vibrations in a condensed phase are discussed in the context of simulated bond distributions in the alloys.

A 12-mer peptide, identified through phage display biopanning, has been used for the first time to induce the rapid formation of ferroelectric (tetragonal) nanocrystalline BaTiO3 at room temperature from an aqueous salt precursor solution at near neutral pH. BaTiO3 is widely used in capacitors, thermistors, displays, and sensors owing to its attractive dielectric, ferroelectric, pyroelectric, optical, and electrochemical properties. Two 12-mer peptides (BT1 and BT2) were selected from a phage-displayed peptide library via binding to tetragonal BaTiO3 powder. While these peptides possessed various types of amino acids, 8 of the 12 amino acids were common to both peptides. Each of these peptides induced the formation of faceted nanoparticles (50-100 nm diameter) from an aqueous precursor solution. X-ray diffraction and selected area electron diffraction patterns obtained from these faceted nanoparticles were consistent with the BaTiO3 compound. Rietveld analyses of the X-ray diffraction patterns yielded good fits to tetragonal crystal structures, with the BaTiO3 formed in the presence of the BT2 peptide exhibiting the most tetragonal character. A coating of the latter BaTiO3 nanoparticles exhibited polarization hysteresis (a well-known characteristic of ferroelectric materials) at room temperature and a relative permittivity of 2200. Such rapid, peptide-induced precipitation at room temperature provides new opportunities for direct BaTiO3 formation on low-melting or reactive materials (e.g., plastics, cloths, bio-organics) and the low temperature integration of BaTiO3 into electronic devices (e.g., on silicon or flexible polymer substrates).

A simple protein-mediated approach for preparing freestanding (silica free) microscale titania structures with morphologies inherited from complex-shaped, three-dimensional (3-D) biosilica templates (diatom frustules) is demonstrated. The silica diatom frustules were exposed in a repetitive alternating fashion to a silica-binding, titania-forming protein (protamine) and then to an aqueous titania precursor to build up a conformal titania-bearing coating. After organic pyrolysis at 500 °C, the conformal, continuous nature of the resulting crystalline anatase titania coating was confirmed by (i) demonstrating that a titania-coated frustule acted as a sensitive electrochemical hydrogen detector and (ii) selectively removing the silica templates to yield freestanding titania structures that retained the 3-D diatom frustule shape.

Atomic layer deposition is used to synthesize Al2O3:ZnO(1:x) nanolaminates with the number of deposition cycles, x, ranging from 5 to 30 for evaluation as optically transparent, electron‐selective electrodes in polymer‐based inverted solar cells. Al2O3:ZnO(1:20) nanolaminates are found to exhibit the highest values of electrical conductivity (1.2 × 103 S cm−1; more than six times higher than for neat ZnO films), while retaining a high optical transmittance (≥80% in the visible region) and a low work function (4.0 eV). Such attractive performance is attributed to the structure (ZnO crystal size and crystal alignment) and doping level of this intermediate Al2O3:ZnO film composition. Polymer‐based inverted solar cells using poly(3‐hexylthiophene) (P3HT):phenyl‐C61‐butyric acid methyl ester (PCBM) mixtures in the active layer and Al2O3:ZnO(1:20) nanolaminates as transparent electron‐selective electrodes exhibit a power conversion efficiency of 3% under simulated AM 1.5 G, 100 mW cm−2 illumination.