The expansion of lithium-ion batteries from consumer electronics to larger-scale transport and energy storage applications has made understanding the many mechanisms responsible for battery degradation increasingly important. The literature in...

No abstract

One of the biggest causes of degradation in lithium-ion batteries is elevated temperature. In this study we explored the effects of cell surface cooling and cell tab cooling, reproducing two typical cooling systems that are used in real-world battery packs. For new cells using slow-rate standardized testing, very little difference in capacity was seen. However, at higher rates, discharging the cell in just 10 minutes, surface cooling led to a loss of useable capacity of 9.2% compared to 1.2% for cell tab cooling. After cycling the cells for 1,000 times, surface cooling resulted in a rate of loss of useable capacity under load three times higher than cell tab cooling. We show that this is due to thermal gradients being perpendicular to the layers for surface cooling leading to higher local currents and faster degradation, but in-plane with the layers for tab cooling leading to more homogenous behavior. Understanding how thermal management systems interact with the operation of batteries is therefore critical in extending their performance. For automotive applications where 80% capacity is considered end-of-life, using tab cooling rather than surface cooling would therefore be equivalent to extending the lifetime of a pack by 3 times, or reducing the lifetime cost by 66%. Due to their high energy and power densities, Lithium-ion batteries are a very important component of electric vehicles, and their use has increased dramatically in recent years as the uptake of hybrid and electric vehicles has increased.1-3 One of the major challenges of using lithium-ion batteries in hybrid and electric vehicles is thermal management, 4 which is important in order to manage degradation at an acceptable rate whilst maximizing the performance of the batteries and reducing the risk of thermal runaway. 5-7Many studies have shown that increased temperature leads to an increase in the rate of degradation, 4,[8][9][10][11] therefore the effectiveness of a thermal management system is vital in order to maximize the lifetime performance of the pack. The design of a good thermal management system for a battery pack should consider both the overall temperature of the pack and both intra-cell and internal thermal gradients. Poor design of thermal management systems could be a major contributing factor in increasing degradation rates to unacceptable levels. 12There are many different techniques that can be used to thermally manage batteries in hybrid and electric vehicles. It is possible to use either air or liquid as the cooling medium, and both of these can be used in either a direct (with cooling medium in contact with the cell) or indirect way. In addition to this, different areas of the cell can be cooled, namely the surfaces of the cell or the cell tabs. 13,14 In general, systems employing air as the cooling medium are considered to be simpler and cheaper to implement, although the performance is limited especially in applications where there is a high heat generation rate or if the batteries are being operated in a high ambient tempe...

Lithium ion batteries are increasingly important in large scale applications where thermal management is critical for safety and lifetime. Yet, the effect of different thermal boundary conditions on the performance and lifetime is still not fully understood. In this work, a two-dimensional electro-thermal model is developed to simulate cell performance and internal states under complex thermal boundary conditions. Attention was paid to model, not only the electrode stack but also the non-core components (e.g. tab weld points) and thermal boundaries, but also the experiments required to parameterize the thermal model, and the reversible heat generation. The model is comprehensively validated and the performance of tab and surface cooling strategies was evaluated across a wide range of operating conditions. Surface cooling was shown to keep the cell at a lower average temperature, but with a large thermal gradient for high C rates. Tab cooling provided much smaller thermal gradients but higher average temperatures caused by lower heat removing ability. The thermal resistance between the current collectors and tabs was found to be the most significant heat transfer bottleneck and efforts to improve this could have significant positive impacts on the performance of li-ion batteries considering the other advantages of tab cooling.

During the operation of a Lithium-Sulfur (Li-S) cell, structural changes take place within both positive and negative electrodes. During discharge, the sulfur cathode expands as solid products (mainly Li2S or Li2S/Li2S2) are precipitated on its surface, whereas metallic Li anode contracts due to Li oxidation/stripping. The opposite processes occur during charge, where Li anode tends to expand due to lithium plating and solid precipitates from the cathode side are removed, causing its thickness to decrease. Most research literature describe these processes as they occur within single electrode cell constructions. Since a large format Li-S pouch cell is composed of multiple layers of electrodes stacked together, and antagonistic effects (i.e. expansion and shrinkage) occur simultaneously during both charge and discharge, it is important to investigate the volumetric changes of a complete cell. Herein, we report for the first time the thickness variation of a Li-S pouch cell prototype. In these studies we used a laser gauge for monitoring the cell thickness variation under operation. The effects of different voltage windows as well as discharge regimes are explored. It was found that the thickness evolution of a complete pouch cell is mostly governed by Li anodes volume changes, which mask the response of the sulfur cathodes. Interesting findings on cell swelling when cycled at slow currents and full voltage windows are presented. A correlation between capacity retention and cell thickness variation is demonstrated, which could be potentially incorporated into Battery Management System (BMS) design for Li-S batteries

Lithium-ion battery development is conventionally driven by energy and power density targets, yet the performance of a lithium-ion battery pack is often restricted by its heat rejection capabilities. It is therefore common to observe elevated cell temperatures and large internal thermal gradients which, given that impedance is a function of temperature, induce large current inhomogeneities and accelerate cell-level degradation. Battery thermal performance must be better quantified to resolve this limitation, but anisotropic thermal conductivity and uneven internal heat generation rates render conventional heat rejection measures, such as the Biot number, unsuitable. The Cell Cooling Coefficient (CCC) is introduced as a new metric which quantifies the rate of heat rejection. The CCC (units W.K −1) is constant for a given cell and thermal management method and is therefore ideal for comparing the thermal performance of different cell designs and form factors. By enhancing knowledge of pack-wide heat rejection, uptake of the CCC will also reduce the risk of thermal runaway. The CCC is presented as an essential tool to inform the cell down-selection process in the initial design phases, based solely on their thermal bottlenecks. This simple methodology has the potential to revolutionise the lithium-ion battery industry.

We present a computer-aided design flow for quantum circuits, complete with automatic layout and control logic extraction. To motivate automated layout for quantum circuits, we investigate grid-based layouts and show a performance variance of four times as we vary grid structure and initial qubit placement. We then propose two polynomialtime design heuristics: a greedy algorithm suitable for small, congestion-free quantum circuits and a dataflow-based analysis approach to placement and routing with implicit initial placement of qubits. Finally, we show that our dataflowbased heuristic generates better layouts than the state-ofthe-art automated grid-based layout and scheduling mechanism in terms of latency and potential pipelinability, but at the cost of some area.

Effective thermal management and tracking of battery degradation are two key challenges in the improved management of battery packs. Entropy change measurement is a non-destructive tool for characterizing both the thermal and structural properties of lithium batteries. However, conventional entropy measurements based on discontinuous potentiometric methods are too time-consuming for practical implementation in battery packs. We present a comprehensive review of potentiometric methods for the entropy change measurement of lithium batteries. We compare conventional and improved discontinuous methods as well as a fully continuous method. Entropy measurements were then made using all the techniques for a solid-state microbattery using a bespoke test system utilising Peltier elements for rapid temperature control. The trade-off between accuracy and speed for the different methods is discussed in detail. In conclusion, the improved discontinuous measurement with significantly reduced voltage relaxation time is recommended for the determination of entropy change during the lithiation/delithiation intercalation reaction in lithium batteries.