The successful development of coal-based integrated gasification combined cycle (IGCC) technology requires gas turbines capable of achieving the dry low nitrogen oxides (NOx) combustion of hydrogen-rich syngas fuels for low emissions and high plant efficiency. Mitsubishi Hitachi Power Systems, Ltd. (MHPS) has been developing a “multiple-injection burner” to achieve the dry low-NOx (DLN) combustion of hydrogen-rich syngas fuels. The purposes of this paper are to present the test results of a multican combustor equipped with multiple-injection burners in an IGCC pilot plant, and evaluate combustor performance by focusing on the effects of flame shapes. The syngas fuel produced in the plant contained approximately 50% carbon monoxide, 20% hydrogen, and 20% nitrogen by volume. In the tests, the combustor with slenderer flames achieved lower NOx emissions of 10.9 ppm (at 15% oxygen), reduced combustor liner and burner plate metal temperatures, and lowered combustion efficiency at the maximum gas turbine load. The test results showed that the slenderer flames were more effective in reducing NOx emissions and liner/burner plate metal temperatures. A comparison with the diffusion-flame combustor demonstrated that the multiple-injection combustors achieved the dry low-NOx combustion of the syngas fuel in the plant.

The successful development of the coal-based integrated gasification combined cycle (IGCC) with carbon capture and storage (CCS) requires gas turbines capable of achieving dry low nitrogen oxide (NOx) combustion of hydrogen-rich syngas fuels for low emissions and high plant efficiency. This chapter describes the development of a "multi-cluster combustor" as a state-of-the-art dry low NOx combustor for hydrogen-rich syngas fuels.The combustor consists of multiple clusters of pairs of one fuel nozzle and one air hole that are installed coaxially. The essence of the design concept is the integration of two key technologies: rapid mixing of fuel and air for low NOx and flame lifting for flashbackresistant combustion. The combustor has been developed in three steps: burner development, combustor development, and feasibility demonstration for practical plants. The combustor was tested with a practical syngas fuel in a multi-can combustor configuration in an IGCC pilot plant in the final step. The combustor achieved the dry low NOx combustion of the syngas fuel in the pilot plant and the test results demonstrated the feasibility for achieving dry low NOx combustion of the syngas fuel in practical plants.

Success of oxygen-blown integrated coal gasification combined cycle (IGCC) technology requires gas turbines capable of achieving dry low nitrogen oxides (NOx) combustion of hydrogen-rich syngas for low emissions and high plant efficiency. The authors have been developing a “multiple-injection burner” to achieve dry low-NOx combustion of such hydrogen-rich fuels using surrogate fuel composed of hydrogen, nitrogen, and methane. The purpose of this paper is to report test results of a multi-can combustor equipped with multiple-injection burners for a practical syngas fuel in an IGCC pilot plant and to evaluate its performance. The syngas fuel consisted of hydrogen, nitrogen, and carbon monoxide up to approximately half of its volume. In the test, the combustor achieved stable and reliable operation from ignition through partial load to the maximum load, and achieved NOx emissions of 15.1 ppm (at 15% oxygen) at the maximum load. These findings demonstrated that the combustor achieves dry low-NOx combustion of the syngas fuel in the IGCC pilot plant.

The successful development of coal-based integrated gasification combined cycle (IGCC) technology requires gas turbines capable of achieving the dry low-nitrogen oxides (NOx) combustion of hydrogen-rich syngas for low emissions and high plant efficiency. Mitsubishi Hitachi Power Systems, Ltd. (MHPS) has been developing a “multiple-injection combustor” to achieve the dry low-NOx combustion of hydrogen-rich syngas. This study suggests an advanced fuel staging comprising a hybrid partial combustion mode to improve the combustor’s part load performance. The purposes of this paper are to present the test results of the combustor with the advanced staging on a syngas fuel in an IGCC pilot plant, and to evaluate its performance. The syngas fuel produced in the plant contained approximately 50% carbon monoxide, 20% hydrogen, and 20% nitrogen by volume. In the test, the advanced staging reduced the maximum NOx at part load to 44 ppm (at 15% oxygen) compared with the initial staging with a maximum NOx of 75 ppm, and attained higher combustion efficiency above 98.7% over the part load range than the initial staging with combustion efficiency above 97.1%. In conclusion, the advanced staging improved the part load performance by achieving lower NOx emissions and higher combustion efficiency.

The successful development of oxygen-blown integrated coal gasification combined cycle (IGCC) technology requires gas turbines capable of achieving the dry low nitrogen oxides (NOx) combustion of hydrogen-rich syngas for low emissions and high plant efficiency. The authors have been developing a "multiple-injection burner" to achieve the dry low-NOx combustion of hydrogen-rich syngas. This burner consists of multiple fuel nozzles and a perforated plate with multiple air holes. At each injection point, one fuel nozzle and one air hole are installed coaxially, so that a fuel jet surrounded by a sheath air jet is injected. The burner achieves low-NOx combustion by mixing fuel and air rapidly with multiple fuel-air coaxial jets, and prevents flashback into the burner by lifting the flame from itself. The purpose of this paper is to present the test results of multi-can combustors equipped with multiple-injection burners in an IGCC pilot plant, and evaluate combustor performance by focusing on the effects of flame shapes. The syngas fuel produced in the plant contained approximately 50% carbon monoxide, 20% hydrogen, and 20% nitrogen by volume. In the tests, the combustor with slenderer flames achieved lower NOx emissions of 10.9 ppm (at 15% oxygen) diluent-free with high stability and high reliability, and reduced both combustor liner and burner plate metal temperatures at the maximum gas turbine load. These findings demonstrated that the multiple-injection combustor achieved the dry low-NOx combustion of the syngas fuel in the plant. : Integrated coal gasification combined cycle (IGCC), Gas turbine, Dry low NOx combustor, Multiple injection burner, Hydrogen-rich syngas fuel