Understanding the asperity damage behaviors of joints during shearing is critical for evaluating the stability of deep underground engineering structures. In this paper, we prepared plaster joints and used them for direct shear tests under different normal stiffness (0–7 MPa/mm) and various shear rate (0.5–20 mm/min) conditions. The effects of normal stiffness and shear rate on mechanical behavior and AE characteristics were studied. With the increase of normal stiffness, the damaged area of the surface of the joint and the weight of the damaged, rough body basically show a linear increase. With the increase of the shear rate, the peak shear stress and the final shear stress of the joint are non-linearly decreased (the decrease rate at the shear rate of 0.5–5 mm/min is much larger than that at the shear rate of 5–20 mm/min), more local cracks appear on the surface of the joint, and the dilatancy of the joint slightly decreases. More than 60% of the acoustic emission signals in the shearing process of the joint are concentrated in the post-peak phase. With the increase of normal stiffness, the cumulative number of acoustic emission impacts and cumulative energy both increase. With the increase in shear rate, the accumulated acoustic emission impact number decreases, and the accumulated AE energy tends to increase when the shear rate is 0.5–5 mm/min and decreases when the shear rate increases to 5–20 mm/min.
To analyze the shear characteristics and mesoscopic failure mechanism of irregular serrated rock discontinuities, a great deal of interview samples of irregular serrated structures were made by 3D printing technology, and laboratory shear tests were carried out on them under different normal stresses. At the same time, PFC numerical simulation software is used to establish relevant models to study the evolution of microcracks and the distribution characteristics of the force chain on the rock discontinuity during the shear process. The results show that the shear mechanical properties of irregular serrated rock discontinuities are affected by normal stress, undulating angle, and undulating height. The shear strength increases with the increase of normal stress and undulating height, and decreases with the increase of undulating angle. The numerical simulation results show that the irregular structural surface cracks under different undulation angles, which first start at the near force end serration root on both sides and further evolve to the adjacent serrations, while the irregular structural surface cracks under different undulation heights, which first start at the serration root with the lowest height and expand to the adjacent serrations. At the same time, the number of cracks increases with the increase of normal stress and the force chain is mainly distributed near the sawtooth surface. The force chain is more concentrated near the near force end sawtooth and at the tip and root of the rest of the sawtooth. At the same time, the direction of the force chain is approximately perpendicular to the force surface of the sawtooth. The research results are helpful in further understanding the shear mechanical properties and differences of irregular serrated rock discontinuities.
Anisotropic discontinuity exists widely in rock masses of mines, tunnels, slopes, water conservancy and hydropower projects. The shear characteristics of bolted anisotropic rock joints are extremely important for the stability design of engineering rock mass. However, few scholars have studied the bolted anisotropic rock joint. The different rock properties on both sides of the rock joint, especially the different rock strengths, will greatly affect the deformation characteristics and failure mode of the rock mass. Based on this, a series of shear tests were carried out on the bolted anisotropic rock joint under different normal stresses, and the characteristics of shear stress–shear displacement curve, shear strength, failure characteristics of the rock joint and deformation characteristics of the bolt are discussed. λ is defined as the strength ratio of upper and lower rock on the structural surface. The results show that the effect of λ on the shear stress–shear displacement curve is not obvious at the pre-fracture stage. The shear stress–shear displacement curve at the pre-breaking stage of the bolt presents a softening stage when the normal stress is equal to 0.5 MPa, tends to be horizontal when the normal stress is equal to 1 MPa and presents a hardening stage when the normal stress is greater than 1 MPa. After the bolt is broken, the shear stress–shear displacement curve presents a stepped-down descent. With the increase in λ, the breaking shear stress of the bolt increases. Elliptic failure occurs on the surface of the bolted anisotropic rock joint, and the length of the major axis of the ellipse decreases with the increase in λ value and normal stress. The bolts with different λ values of anisotropic rock joint show “Z-shaped” tensile bending deformation characteristics after shear fracture, and the horizontal and vertical components of the bolt deformation decrease with the increase in λ value and normal stress. The fracture shear displacement of the bolt increases with the increase in normal stress and decreases with the increase in λ value. The research results are helpful to further understand the shear mechanical characteristics and differences of bolted rock joints and provide a reference for solving the engineering problems of the composite layered rock mass.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.