Performance of classic sound absorbing materials strictly depends on their thickness, with a minimum of one-quarter wavelength to reach full sound absorption. In this paper, we report ultrathin sound absorbing panels that completely absorb sound energy with a thickness around one percent of wavelength. The strategy is to bend and coil up quarter-wavelength sound damping tubes into 2D coplanar ones, and embed them into a matrix to form sound absorbing panel. Samples have been designed and fabricated by 3D printing. Efficacies of sound absorption by these panels were validated through good agreement between theoretical analysis and experimental measurements.

DLP 3D printed ionic hydrogels are designed as sensitivity-improved electrodes in a skin-like sensor.

Solar steam generation is one of the most promising solar-energy-harvesting technologies to address the issue of water shortage. Despite intensive efforts to develop high-efficiency solar steam generation devices, challenges remain in terms of the relatively low solar thermal efficiency, complicated fabrications, high cost, and difficulty in scaling up. Herein, a double-network hydrogel with a porous structure (p-PEGDA-PANi) is demonstrated for the first time as a flexible, recyclable, and efficient photothermal platform for low-cost and scalable solar steam generation. As a novel photothermal platform, the p-PEGDA-PANi involves all necessary properties of efficient broadband solar absorption, exceptional hydrophilicity, low heat conductivity, and porous structure for high-efficiency solar steam generation. As a result, the hydrogel-based solar steam generator exhibits a maximum solar thermal efficiency of 91.5% with an evaporation rate of 1.40 kg m h under 1 sun illumination, which is comparable to state-of-the-art solar steam generation devices. Furthermore, the good durability and environmental stability of the p-PEGDA-PANi hydrogel enables a convenient recycling and reusing process toward real-life applications. The present research not only provides a novel photothermal platform for solar energy harvest but also opens a new avenue for the application of the hydrogel materials in solar steam generation.

No abstract

Three-dimensional printing was used to fabricate various metallic structures by directly integrating a Br-containing vinyl-terminated initiator into the 3D resin followed by surface-initiated atomic-transfer radical polymerization (ATRP) and subsequent electroless plating. Cu- and Ni-coated complex structures, such as microlattices, hollow balls, and even Eiffel towers, were prepared. Moreover, the method is also capable of fabricating ultralight cellular metals with desired structures by simply etching the polymer template away. By combining the merits of 3D printing in structure design with those of ATRP in surface modification and polymer-assisted ELP of metals, this universal, robust, and cost-effective approach has largely extended the capability of 3D printing and will make 3D printing technology more practical in areas of electronics, acoustic absorption, thermal insulation, catalyst supports, and others.

In this article, we describe a writable particle-free ink for fast fabrication of highly conductive stretchable circuits. The composite ink mainly consists of soluble silver salt and adhesive rubber. Low toxic ketone was employed as the main solvent. Attributed to ultrahigh solubility of silver salt in short-chain ketone and salt-assisted dissolution of rubber, the ink can be prepared into particle-free transparent solution. As-prepared ink has a good chemical stability and can be directly filled into ballpoint pens and use to write on different substrates to form well adhesive silver salt-based composite written traces as needed. As a result of high silver salt loading, the trace can be converted into highly conductive silver nanoparticle-based composites after in situ reduction. Because of the introduction of adhesive elastomeric rubber, the as-formed conductive composite written trace can not only maintain good adhesion to various substrates but also show good conductivity under various deformations. The conductivity of written traces can be enhanced by repeated writing-reduction cycles. Different patterns can be fabricated by either direct handwriting or hand-copying. As proof-of-concept demonstrations, a typical handwriting heart-like circuit was fabricated to show its capability to work under different deformations, and a pressure-sensitive switch was also manufactured to present pressure-dependent change of resistance.

No abstract

Initiator integrated 3D printing, namely i3DP, was developed by incorporating a vinyl-terminated initiator into UV curable resin to make functional structural materials that enable genetic post-printing surface-initiated modification. Taking advantage of 3D printing and surface-initiated ATRP, the feasible i3DP makes 3D printed complex architectures possible for nearly any desired surface modification for various applications, for example, even pouring water into a sieve was readily achieved.