The article presents the results of research on the efficiency of photovoltaic (PV) modules cooled with water. The aim of the experiment was to improve the working conditions of solar modules. A temperature decrease was obtained for the PV module by pouring cool tap water onto the upper surface of the modules, either in imitation of rain or as a water film. The power of the cooled and non-cooled devices were then compared. The temperature of the cooled modules dropped to almost 25 °C, whilst the temperature of the non-cooled module was 45 °C. The best results were achieved by cooling modules with a water film, since there were no water splashes, and the continuous cooling of the surface leads to a 20% increase in power. During the test, the non-cooled module attained a maximum power of 105.3 W/m2, compared to 125.5 W/m2 for its cooled counterpart. Cooling the module, therefore, resulted in a power increase of 20.2 W/m2. The results of the work may be of particular interest for small installations, especially because it cleans the modules while providing an increase in power.

With sustainable energy being the key to reaching climate neutrality, the utilization of non-wooden biomass is a necessity. This article compares the emissions and efficiency of combusting a number of types of agrobiomass and wood pellets. A comparison was made on a moving grate pellet burner mounted in a boiler, where flue gas had a vertical flow via two pass heat exchangers with turbulization elements. Tests were conducted on wood pellets (ENPlus), miscanthus straw pellets, sunflower husk pellets, and corn stover pellets. During combustion, both wood and miscanthus pellets met the PN-EN 303-5:2012 emission and efficiency requirements. Corn stover pellets met the requirement on the nominal capacity. Sunflower husk pellets are characterized by excessive CO and particulate matter emissions. Sunflower husk pellets were the most problematic fuel from the point of view of the results of this research. During combustion of the miscanthus straw pellets there was a need to decrease the nominal heating capacity due to ash sintering.

Abstract:The outdoor measurements (during two months experiment) of photovoltaic silicon and CIGS modules as well as simulation of energy production during the period experiment are presented in this paper. This paper offer comparison of construction and electrical characteristics of multicrystalline silicon based modules and CIGS based modules. The measuring system for PV modules efficiency research is shown. The nominal power of installed modules is 250 W for m-Si and 280 W for CIGS modules. The energy production in outdoor conditions at direct current side and alternating current side of each photovoltaic panel was measured. Each PV panel was also equipped with temperature sensor for screening panel temperature. The photovoltaic panels were connected to the electrical network with micro inverters. To determine the influence of irradiance at sunshine on power conversion efficiency of PV panels, the pyranometer was installed in the plane of the modules. Measurement of the instantaneous power and irradiance gave the information about the efficiency of a particular photovoltaic panels. In the paper all data from research installation were analysed to present the influence of solar cell technology on the power conversion efficiency. The results of energy production show that m-Si module produced more energy from square meter (30.9 kWh/m 2 ) than CIGS module (28.0 kWh/m 2 ). Thin film module shows the higher production per kWp than multicrystalline module: 217.3 kWh/kWp for CIGS and 201.9 kWh/kWp for m-Si. The energy production simulation (made by PV SOL software and outdoor measurements test are in the good agreement. Temperature power coefficient for the CIGS module is twice lower than for the multicrystalline silicon module: 0.56%/°C and 0.35%/°C for m-Si and CIGS modules, respectively. The obtained results revealed strong influence of irradiance and temperature on energy production by PV panels. Performed studies have a large field of potential application and could improve designing process of PV installation.

No abstract

The Centre of Sustainable Development and Energy Savings of the Faculty of Geology, Geophysics and Environmental Protection of AGH University of Science and Technology in Miekinia conducts research and educational activities in the field of renewable sources of energy, geothermal heat pumps especially. Growing interest in using the renewable energy sources (RES) is reflected upon the interest in such a discipline of studies. Many people declare intention of studying RES. This is a modern discipline, opened at AGH University of Science and Technology in 2003 as the first in Poland. Since 2012, when the Centre was open ca. 8000 people (including students, pupils, local governments and communities) were educated here. Not only geothermal energy is a main focus attention field. In the Centre other renewable sources of energy are also researched. This include solar energy (both photovoltaic and thermal), solid fuel boilers and wind energy. The Centre is heated by heat pumps with ground sources which are simultaneously use by students for practice and measurements. There are didactic heat pumps with temperature and pressure sensors and electric meters to be used by students during measurements. The Centre is in disposal of self-constructed Thermal Response Test device for thermal parameters measurements. In a stand for testing ground-source brine heat pumps for central heating and hot domestic water preparation research are conducted on the COP heat pump efficiency in accordance with the PN-EN 14511 standard. The Centre works on the prototyping of new, innovative heat pumps.

No abstract

In the municipal and residential sector in Poland, as many as 50% of households are heated by solid fuel boilers. Most often these are, unfortunately, inefficient boilers, fired with low-quality coal. This study characterizes the market of boilers for solid fuels in Poland, and also presents the main apportionment of these devices, due to the different criteria that characterize them. The current legal changes in the scope of energy and emission requirements for solid fuel boilers are also discussed. The main purpose of this work is to analyze the real efficiency of the solid fuel over-fired boiler used, depending on the fuel burned in it. The process of burning selected fuels (seasoned wood, coal and pea coal) in the boiler was preceded by tests of these fuels to determine their energy parameters, such as moisture, ash content, the share of volatile matter and calorific value. In the next step, the energy efficiency obtained by the tested solid fuel boiler during the combustion of selected solid fuels was compared. The highest efficiency was achieved during the combustion of pea coal, and the lowest was achieved during the combustion of wood. In any case, the nominal efficiency value was achieved. Solutions that could improve the quality of the combustion process in this type of boiler were proposed.

No abstract