Microalloyed steels are used in the forging of many automotive parts like crankshafts and connecting rods. They are hot worked in a sequence of stages that includes the heating to the soaking temperature, followed by forging steps, and finally the controlled cooling to define the microstructure and mechanical properties. In this work it was investigated the thermomechanical behavior and the microstructural evolution of a Ti-V microalloyed steel in the phase transition region. Torsion tests were done with multiple steps with true strain equal to 0.26 in each step. After each torsion step the samples were continuous cooled for 15 seconds to simulate hot forging conditions. These tests provided results for the temperature at the beginning of the phase transformation, and allowed to analyze the microstructural changes. Also, workability tests were held to analyze the microstructural evolution by optical and scanning electron microscopy. Results from the torsion tests showed that the temperature for the beginning of phase transformation is about 700 ºC. Workability tests held at 700 ºC followed by water-cooling presented microstructures with different regions: strain hardened, and static and dynamic recrystallized. Workability tests at 700 ºC followed by air-cooling showed a complex microstructure with ferrite, bainite and martensite, while tests at 650 and 600 ºC followed by water-cooling showed a microstructure with allotriomorphic ferrite present in the grain boundaries of the previous austenite. Os aços microligados são usados em peças automotivas forjadas, tais como girabrequins e bielas. Essas peças são trabalhadas a quente em uma seqüência de estágios, que inclui o aquecimento até a temperatura de encharque, seguido por vários passes de forjamento, e, finalmente, há um resfriamento controlado para definir a microestrutura e propriedades mecânicas. Nesse trabalho, foram investigados o comportamento termomecânico e a evolução microestrutural de um aço microligado Ti-V na região de transição de fase. Os testes de torção foram feitos em múltiplos passos com deformação verdadeira de 0,26 em cada passo. Após cada passo de torção, as mostras foram resfriadas continuamente por 15 segundos para simular as condições de forjamento a quente. Esses testes forneceram resultados da temperatura de início de transformação de fase e permitiram analisar as mudanças de microestrutura. Foram, também, realizados os testes de trabalhabilidade para analisar a evolução microestrutural por microscopia ótica e eletrônica de varredura. Os resultados dos testes de torção mostraram que a temperatura de início de transformação de fase está em torno de 700ºC. Os testes de trabalhabilidade feitos a 700ºC seguidos por resfriamento em água apresentaram microestruturas com características distintas: regiões encruadas e de recristalização estática e dinâmica. Os testes de trabalhabilidade de 700ºC seguidos por resfriamento ao ar mostraram uma complexa microestrutura de ferrita, bainita e martensita, enquanto que os testes feitos em 650 e 600ºC ...
Numerical and experimentalanalysis of the microstructural evolution during cross wedge rolling of V-Ti microalloyed steel (Análise numérica e experimental da evolucão microestrutural durante a laminação transversal com cunha de um aço microligado ao V-Ti)
ResumoO desenvolvimento de processos de conformação para a melhoria da qualidade dos produtos, bem como a diminuição das perdas de matéria-prima e, também, da energia são os principais enfoques de várias pesquisas no Brasil e no exterior. Entre essas pesquisas está o processo Cross Wedge Rolling (CWR), que vem sendo estudado nos últimos anos para a substituição do recalque horizontal a quente na fabricação em uma única operação de eixos escalonados, pinos, eixos excêntricos e outros componentes. Esse processo é caracterizado pela deformação plástica de um tarugo cilíndrico pela ação de ferramentas em formato de cunha montadas sobre placas planas que se movem tangencialmente uma em relação à outra. O objetivo desse trabalho foi analisar o comportamento termomecânico de um aço laminado no CWR por simulação numérica e a evolução microestrutural dada pela simulação física. Os resultados mostram um comportamento do material de recristalização dinâmica e suas microestruturas do campo austenítico com aspectos de alto grau de refinamento.
Palavras
Upon hot strip mill of titanium Interstitial Free (IF) steels, during cooling from austenite to ferrite region, the level of interstitial elements not removed by steelmaking process is dropped down by Ti that combines with N, C and S. Some authors [1-3] have reported that the traditional precipitation sequence TiN, TiS, Ti4C2S2 and TiC occurs with freestanding particles formed by nucleation and growth processes. Other authors [4] have indicated that the transformation from TiS to Ti4C2S2 may be considered as a hybrid of shear and diffusion, i.e., faulted Ti8S9 (9R) + 10[Ti] + 9[C] → 41/2Ti4C2S2 (or H for its hexagonal crystal structure). At low temperature (≤930°C), the stabilization process continues through epitaxial growth of carbides on H phase. to study the evolution of precipitation upon hot strip mill conditions, samples of a Ti - IF steel were subjected to double straining tests [5] by means of a computerized hot torsion machine, at 1000 °C and 920 °C, with strain rate of 1 s-1 and interpass times ranging from 0.5 to 100 s.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.