Hydrogels consist of hydrophilic polymer networks dispersed in water. Many applications of hydrogels rely on their unique combination of solid-like mechanical behavior and water-like transport properties. If the temperature is lowered below 0 °C, however, hydrogels freeze and become rigid, brittle, and non-conductive. Here, a general class of hydrogels that do not freeze at temperatures far below 0 °C, while retaining high stretchability and fracture toughness, is demonstrated. These hydrogels are synthesized by adding a suitable amount of an ionic compound to the hydrogel. The present study focuses on tough polyacrylamide-alginate double network hydrogels equilibrated with aqueous solutions of calcium chloride. The resulting hydrogels can be cooled to temperatures as low as -57 °C without freezing. In this temperature range, the hydrogels can still be stretched more than four times their initial length and have a fracture toughness of 5000 J m . It is anticipated that this new class of hydrogels will prove useful in developing new applications operating under a broad range of environmental and atmospheric conditions.
Dynamic crosslinking of extremely stretchable hydrogels with rapid self-healing ability is described. Using this new strategy, the obtained hydrogels are able to elongate 100 times compared to their initial length and to completely self-heal within 30 s without external energy input.
The development of hydrogels for cartilage replacement and soft robotics has highlighted a challenge: load-bearing hydrogels need to be both stiff and tough. Several approaches have been reported to improve the toughness of hydrogels, but simultaneously achieving high stiffness and toughness remains difficult. Here we report that alginate-polyacrylamide hydrogels can simultaneously achieve high stiffness and toughness. We combine short-and long-chain alginates to reduce the viscosity of pregel solutions and synthesize homogeneous hydrogels of high ionic cross-link density. The resulting hydrogels can have elastic moduli of ∼1 MPa and fracture energies of ∼4 kJ m −2 . Furthermore, this approach breaks the inverse relation between stiffness and toughness: while maintaining constant elastic moduli, these hydrogels can achieve fracture energies up to ∼16 kJ m −2 . These stiff and tough hydrogels hold promise for further development as load-bearing materials.
Using strong fibers to reinforce a hydrogel is highly desirable but difficult. Such a composite would combine the attributes of a solid that provides strength and a liquid that transports matter. Most hydrogels, however, are brittle, allowing the fibers to cut through the hydrogel when the composite is loaded. Here we circumvent this problem by using a recently developed tough hydrogel. We fabricate a composite using an alginate-polyacrylamide hydrogel reinforced with a random network of stainless steel fibers. Because the hydrogel is tough, the composite does not fail by the fibers cutting the hydrogel; instead, it fails by the fibers pulling out of the hydrogel against friction. Both stiffness and strength can be increased significantly by adding fibers to the hydrogel. Before failure the composite dissipates a significant amount of energy, at a tunable level of stress, attaining large deformation. Potential applications of tough hydrogel composites include energy-absorbing helmets, tendon repair surgery, and stretchable biometric sensors.
There is a large demand for fabrics that can survive high-temperature fires for an extended period of time, and protect the skin from burn injuries. Even though fire-resistant polymer fabrics are commercially available, many of these fabrics are expensive, decompose rapidly, and/or become very hot when exposed to high temperatures. We have developed a new class of fire-retarding materials by laminating a hydrogel and a fabric. The hydrogel contains around 90% water, which has a large heat capacity and enthalpy of vaporization. When the laminate is exposed to fire, a large amount of energy is absorbed as water heats up and evaporates. The temperature of the hydrogel cannot exceed 100 °C until it is fully dehydrated. The fabric has a low thermal conductivity and maintains the temperature gradient between the hydrogel and the skin. The laminates are fabricated using a recently developed tough hydrogel to ensure integrity of the laminate during processing and use. A thermal model predicts the performance of the laminates and shows that they have excellent heat resistance in good agreement with experiments, making them viable candidates in life saving applications such as fire-resistant blankets or apparel.
The effects of dislocation climb on plastic deformation during loading and unloading are studied using a two-dimensional discrete dislocation dynamics model. Simulations are performed for polycrystalline thin films passivated on both surfaces. Dislocation climb lowers the overall level of the stress inside thin films and reduces the work hardening rate. Climb decreases the density of dislocations in pile-ups and reduces back stresses. These factors result in a smaller Bauschinger effect on unloading compared to simulations without climb. As dislocations continue to climb at the onset of unloading and the dislocation density continues to increase, the initial unloading slope increases with decreasing unloading rate. Because climb disperses dislocations, fewer dislocations are annihilated during unloading, leading to a higher dislocation density at the end of the unloading step. V C 2014 AIP Publishing LLC. [http://dx
Purpose A strong isotropic material that is both biocompatible and biodegradable is desired for many biomedical applications, including rotator cuff repair, tendon and ligament repair, vascular grafting, among others. Recently, we developed a technique, called “bioskiving” to create novel 2D and 3D constructs from decellularized tendon, using a combination of mechanical sectioning, and layered stacking and rolling. The unidirectionally aligned collagen nanofibers (derived from sections of decellularized tendon) offer good mechanical properties to the constructs compared with those fabricated from reconstituted collagen. Methods In this paper, we studied the effect that several variables have on the mechanical properties of structures fabricated from tendon slices, including crosslinking density and the orientation in which the fibers are stacked. Results We observed that following stacking and crosslinking, the strength of the constructs is significantly improved, with crosslinked sections having an ultimate tens ile strength over 20 times greater than non-crosslinked samples, and a modulus nearly 50 times higher. The mechanism of the mechanical failure mode of the tendon constructs with or without crosslinking was also investigated. Conclusions The strength and fiber organization, combined with the ability to introduce transversely isotropic mechanical properties makes the laminar tendon composites a biocompatiable material that may find future use in a number of biomedical and tissue engineering applications.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.