In this paper, we used tannic acid (TA) functionalized carbon nanotubes (TCNTs), and silver nanowires (AgNWs) to construct a new type of transparent conductive film (TCF) with a double-layered conductive network structure. The hybrid film exhibits excellent light transmittance, high electrical conductivity, ultra-flexibility, and strong adhesion. These outstanding performances benefit from the filling and adhesion of hydrophilic TCNT layers to the AgNW networks. Besides, we introduced the post-treatment process of mechanical pressing and covering polymer conductive polymer PEDOT:PSS, which obtained three layers of TCNT/AgNW/PEDOT hybrid film and greatly improved the comprehensive properties. The hybrid film can reach a sheet resistance of 9.2 Ω sq−1 with a transmittance of 83.4% at 550 nm wavelength, and a low root mean square (RMS) roughness (approximately 3.8 nm). After 10 000 bends and tape testing, the conductivity and transmittance of the hybrid film remain stable. The resistance of the film has no significant degradation after 14 d of exposure to high temperature of 85 °C and humidity of 85%, indicating excellent stability. The organic light-emitting diodes (OLEDs) with TCNT/AgNW/PEDOT hybrid film as anode exhibit high current density and luminosity, confirming this process has considerable potential application in photovoltaic devices.

No abstract

Transparent conductive films with high stability were prepared by embedding silver nanowires in colorless polyimide and adding a protective layer of exfoliated graphene. The films exhibit great light transmission and conductivity with a sheet resistance of 22 Ω/sq at transmittance of 83%. Due to its special embedded structure, the adhesion between the conductive layer and the substrate was too strong to peel off from the substrate. In addition, the most outstanding advantage is the ultra-high stability of the films, including high mechanical robustness, strong chemical corrosion resistance and high operating voltage capacity. The OLED devices prepared based on this transparent conductive electrode exhibit comparable efficiency to ITO based devices, with C.E.max = 2.78 cd/A, P.E.max= 1.89 lm/W, EQEmax = 0.89%. What’s more, the efficiencies were even higher than that of ITO devices when the operating voltage of the device exceeds 5 V. The above performances show that the transparent conductive electrode based on this structure has high potential for application in organic electronic devices.

The rapid development of the Internet of Things has promoted the application of wearable devices in human's daily life and industrialization. Strain sensors play an indispensable role as a member of wearable devices. Here, a strain film sensor with multi‐walled carbon nanotubes (MWCNTs) and Ti3C2TX MXene, which is obtained by vacuum‐assisted filtration and integrated onto a thermoplastic polyurethane substrate, is developed. Since the MWCNTs and Ti3C2TX MXene composite sensor has a characteristic ‘mud‐brick’ microstructure. The sensor has the ability to detect various human movements, such as, bending of finger joints, wrists, elbow joints, and shoulder. The sensors show excellent mechanical property and can be folded more than 2000 times without failure. It also exhibits short response time, low detection limit, and wide range of use. In addition, the sensor shows excellent electrical heating performance. The temperature of the composite film can rise to 96.6 °C in a short period of time even under low voltage power supply (25 V). It likewise proves its excellent performance in terms of cyclability and long‐time heating capability. The film has low production cost, easy preparation method, and simple operation. The MWCNT/Ti3C2TX MXene film can be integrated into wearable devices and shows great potential for future applications.

Traditional conductive fabrics are prepared by the synthesis of conductive polymers and the coating modification of metals or carbon black conductive materials. However, the conductive fabrics cause a significant decline in performance after washing or mechanical wear, which limits their application. Moreover, the single function of the traditional conductive fabric is also the reason that limits its wide application. In order to prepare a wearable, stable, high-performance, washable, multifunctional conductive fabric, we have carried out related research. In this work, polydopamine was used as a bonding layer, an adsorption reduction layer, and a protective layer to improve the bonding between silver nanoparticles and carbon nanotubes (CNTs) on the polyester fabric surface so as to prepare a multifunctional conductive fabric with a high-stability "sandwich" structure, in which a Ag-NPS@CNT structure acting as an intermediate conductive layer formed on the inner layer PDA@CNT by electroless silver plating and the outermost layer PDA@ CNT coated on the surface of the intermediate conductive layer by the impregnation-drying method. The sheet resistance of an E-Fabric can reach 2.11 Ω/□ due to the uniform and dense conductive path formed by the special structure Ag-NPs@CNT. At a low voltage of 1.5 V, the E-Fabric can reach 117 °C in 50 s and remain stable. The electrical conductivity and current heating properties of the E-Fabric remain good even after multiple washing or bending tests. Due to its stable and outstanding electrical conductivity, the E-Fabric has an electromagnetic shielding efficiency (SE T ) of 35.3 dB in the X-band (8.2−12.4 GHz). In addition, E-Fabricbased spin-coated poly(methyl methacrylate) or polydimethylsiloxane electrodes exhibit excellent performance in nanogenerators. Through the low-frequency friction of the human body, transient voltages up to 4 V can be generated from a 2 cm × 2 cm electrode sample. The output power of a single generator can reach about 12 nW/cm 2 . Therefore, an E-Fabric is considered to have great potential in the fields of electric heating, electromagnetic shielding, and smart wearable devices.