Abstract. In this study, a novel rotary cleaning device was used for the separation and cleaning of wheat grains. This research analyzed the influence of the inclination angle of the sieve drum (K) of the device on the quality of these processes. In this article, the results obtained for four selected rotational speeds (nb) of the sieve drum are presented. The quality of the separation and cleaning of the wheat grains was evaluated using three cleaning process parameters: coefficient of plump grain mass separation (Wz), coefficient of fine impurities separation (Wd), and total coefficient of cleaning effectiveness (E). Based on statistical analysis of the results, the inclination angle of the sieve drum had a significant effect on the quality of the wheat grain separation process. Coefficient Wz was highest for sieve drum inclination angles of K = 0° and K = 2.5°, whereas Wd was highest for K = -2.5°. The total coefficient of cleaning effectiveness (E) was characterized by different values for different inclination angles of the sieve drum. Keywords: Cleaning effectiveness, Conical sieve, Rotary cleaning device, Wheat grain cleaning.
The paper presents the results of the research into the impact of impregnation of wood on its bending strength and elastic modulus under normal conditions and after thermal treatment and investigates its structural reliability. Pinewood, non-impregnated and pressure impregnated with a solution with SiO2 nanoparticles, was used in this research. The use of nanoparticles decreases the flammability of timber among others. Some of the tested samples were treated at 250 °C. This temperature corresponds to the boundary of the self-ignition of wood. This elevated temperature was assumed to be reached by a given speed of heating within 10 min, and then the samples were stored in these conditions for 10 and 20 min. The tests demonstrate that the bending strength of the impregnated wood was slightly improved, the impregnation did not impact the elastic modulus of the material in all such conditions, and the residual strength decreased less for the wood impregnated after being exposed to the elevated temperatures. The reliability analysis proves a positive effect of impregnation with a solution with SiO2 on the durability of wood, both after being exposed to normal and elevated temperatures. The distribution of the failure rates indicates a more intensive degradation of non-impregnated wood. The distribution of the survival function demonstrates a more probable non-destruction of impregnated wood after elevated temperature conditions.
Artykuł zawiera przegląd najnowszych technologii druku 3D obiektów z metalu. Technologie te sklasyfikowano ze wzglę-du na sposób podawania oraz łączenia materiału. Wskazano wady i zalety poszczególnych rozwiązań podawania materiału metalowego. Przedstawiono skrótowy opis technologii druku 3D z użyciem materiału metalowego oraz zestawiono producentów oferujących urządzenia do danej technologii. SŁOWA KLUCZOWE: druk 3D, obiekty metalowe, technika przyrostowaThe article presents the newest technologies of the 3D printing of metal objects. The technologies were classified on account of the way of laying and joining material. The research results are indicated the advantages and the disadvantages of the various methods of joining metal material. There is presented a brief description of the technology of the 3D printing which using a metal material, and lists of manufacturers who offering the device in the technology.
KEYWORDS: 3D printing, metal objects, additive techniqueDruk trójwymiarowy (3D), należący do przyrostowych technik wytwarzania, jest wykorzystywany już od ponad 30 lat. Pionierem w tej dziedzinie jest Charles Hull, który w 1984 r. opracował technologię zwaną stereolitografią. Polega ona na utwardzaniu fotopolimerów za pomocą wiązki promieni ultrafioletowych. W kolejnych latach nastą-pił wzrost zainteresowania tematyką druku przestrzennego. Przełomowe było ostatnie dziesięciolecie, kiedy druk 3D został "uwolniony" od obowiązywania pierwszych praw patentowych, które właśnie wygasały. Dodatkowo projekt RepRap (replicating rapid prototyper) spopularyzował technikę druku przestrzennego za sprawą możliwości jego wykorzystywania -na zasadach wolnego dostępu do schematów urządzenia czy oprogramowania. Obecnie techniki przyrostowe znajdują się w obszarze zainteresowania wielu branż przemysłu. Potrzeby są jednak skierowane na zastosowanie technik 3D do tworzenia obiektów metalowych.
Podział technologiiTechnika przyrostowego wykonywania metalowych obiektów uwzględnia: formę materiału roboczego oraz sposób jego łączenia i podawania. Dobór poszczególnych rozwiązań określa rodzaj technologii, w jakiej urządzenie będzie pracowało. Obecnie wyróżnia się wiele technologii druku 3D obiektów metalowych, a każda ma wyjąt-kowe cechy. Wybór najlepszej technologii zależy przede wszystkim od potrzeb wykonawcy i zamawiającego obiekty 3D z metalu. Te wymagania to najczęściej: krótki czas i niski koszt wytworzenia, odpowiednie właściwości mechaniczne materiału, wysoka dokładność (wierne odwzorowanie) czy druk skomplikowanych geometrycznie modeli. Na rys. 1 przedstawiono autorski podział technologii druku 3D obiektów metalowych.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.