Purpose – The purpose of this paper is to evaluate the influence of assembly parameters on lead-free solder joints reliability in Package-on-Package (PoP) Technology and demonstrate factors important for this issue. Design/methodology/approach – Two types of soldering materials and three different assembly procedures were used for assembly of PoP system. The reliability properties of assembled PoP systems were investigated using accelerated aging and periodic resistance measurements of daisy-chain solder joints systems. The purpose of such approach was to determine which soldering material (flux or solder paste) as well as which assembly process parameter (dipping depth of upper component in soldering material), would provide better reliability properties of the solder joints in the PoP system. Findings – It was stated that both selected flux and solder paste dedicated to assembly of PoP systems can be utilized in soldering of PoP applications. More reliable PoP systems applications require larger attention regarding materials selection and assembly parameters. It is recommended 50 per cent dipping depth of ball’s height into soldering material during upper PoP component assembly for more reliable applications. For less demanding PoP systems, the process window from 30 up to 70 per cent is acceptable. All observed failures after thermal shocks occurred in upper PoP components. Originality/value – This paper explains how materials and assembly parameters have influence on lead-free solder joints reliability in PoP systems. Especially, influence of process window for dipping procedure of upper components balls into soldering material was presented.
Modern electronic devices are more and more complex and multifunctional. It could be done by producing faster and more reliable active components and increasing number of passives and interconnections' density. To form such complex devices one can embed components in substrate of printed circuit board (PCB) or build multilayer boards. The other way is to form multi-terminal passive components to spare free surface and decrease number of interconnections. Authors created three-terminal thin-film (TF) resistors embedded in PCBs and investigated their selected properties such as resistance repeatability, long term stability, pulse durability and thermal characteristics.
Abstract. Noise studies of planar thin-film Ni-P resistors made in/on Printed Circuit Boards, both covered with two different types of cladding or uncladded have been described. The resistors have been made of the resistive-conductive-material (Ohmega-Ply ) of 100 Ω/sq. Noise of the selected pairs of samples has been measured in the DC resistance bridge with a transformer as the first stage in a signal path. 1/f noise caused by resistance fluctuations has been found to be the main noise component. Parameters describing noise properties of the resistors have been calculated and then compared with the parameters of other previously studied thin-and thick-film resistive materials.
This paper presents systematic studies of electrical, noise and long-term stability parameters of resistors (thinfilm or polymer thick-film) and capacitors embedded in Printed Circuit Boards (PCBs). The temperature dependence of resistance or capacitance were determined in a wide temperature range (from -180 o C to 130 o C) and analyzed as a function of geometry of passives and cladding process. The in-situ accelerated ageing process (basic properties of passives measured directly at ageing conditions) was carried out to perform long-term behavior analysis. Low frequency noise measurements were made in room temperature using noise spectra measurements in dc bridge configuration.The R(T) characteristics are linear with almost constant, negative value of differential TCR (of about -60 ppm/K for 100 Ω/sq Ni-P resistors). Both groups of investigated resistors revealed similar range of relative resistance changes after ageing processes but the results showed the quite different behavior of both groups versus time. It means that the dynamics of ageing changes was different. Only positive resistance changes were observed for Ni-P resistors, whereas the shape of characteristics for polymer ones were much more complex, exhibited increase as well as decrease in resistance under environmental exposure. 1/f noise generated by resistance fluctuations was found as the main noise component but the significant difference of noise level was observed for both groups of investigated resistors.The C(T) characteristics are nonlinear with larger capacitance changes at higher temperature. Capacitors exposed to elevated temperature exhibited capacitance and dissipation factor decrease. The relative changes were from the range from -12% to -2% for capacitance and up to -60% for dissipation factor. The value of relative drift of parameters was dependent strongly on dielectric composition and size. Moreover the results revealed nonlinear characteristics in temperature domain as well.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.