Fluoroethylene carbonate (FEC) and vinylene carbonate (VC) are the most frequently used electrolyte additives to enhance the lifetime of anode materials in Li-ion batteries, but for silicon it is still ambiguous when FEC or VC is more beneficial. Herein, a low-cost nanostructured silicon/carbon anode derived from HSiCl3 is tailored by the rational choice of the additive, to obtain an anode material outperforming current complex silicon structures. We demonstrate highly reversible areal capacities of up to 5 mAh/cm2 at 4.4 mg/cm2 mass loading, a specific capacity of 1280 mAh/gAnode, a capacity retention of 81 % after 500 deep-discharge cycles versus lithium metal and successful full-cell tests with high-voltage cathodes meeting the requirements for real application. Electrochemical impedance spectroscopy and post-mortem investigation provide new insights in tailoring the interfacial properties of silicon-based anodes for high performance anode materials based on an alloying mechanism with large volume changes. The role of fluorine in the FEC-derived interfacial layer is discussed in comparison with the VC-derived layer and possible degradation mechanisms are proposed. We believe that this study gives a valuable understanding and provides new strategies on the facile use of additives for highly reversible silicon anodes in Li-ion batteries
In this study, APS and HVOF processes have been used to prepare alumina (Al 2 O 3 ) and magnesium spinel (MgAl 2 O 4 ) coatings designed for insulating applications. The electrical characteristics, i.e., dielectric strength and electrical resistance (electrical resistivity) were investigated using different methods: dielectric breakdown test, direct current (DC) measurements, and electrochemical impedance spectroscopy (EIS). The electrical resistance was measured at room temperature at different relative humidity (RH) levels (from 6% RH to 95% RH) as well as at 200°C. The coating microstructure, phase composition, and water vapor sorption were studied. Differences in the electrical insulating properties due to the different coating system characteristics are discussed. Of the coatings and conditions investigated in this study, the HVOF spinel coatings showed superior dielectric breakdown strength and electrical resistance stability at high humidity levels.
In this work the microstructural characteristics and electrical insulating properties of thermally sprayed alumina coatings produced by suspension-HVOF (S-HVOF) and conventional HVOF spray processes are presented. The electrical resistance at different relative air humidity (RH) levels (from 6 to 97% RH) and values of dielectric strength were investigated by direct current electrical resistance measurements, electrochemical impedance spectroscopy, and dielectric breakdown tests. Relationships between electrical properties and coating characteristics are discussed. At low humidity levels (up to 40% RH) the electrical resistivities of S-HVOF and HVOF coatings were on the same order of magnitude (10 11 XAEm). At a very high humidity level (97% RH) the electrical resistivity values for the S-HVOF coatings were in the range 10 7 -10 11 XAEm, up to five orders of magnitude higher than those recorded for the HVOF coating (orders of magnitude of 10 6 XAEm). The better electrical resistance stability of the suspension-sprayed Al 2 O 3 coatings can be explained by their specific microstructure and retention of a higher content of a-Al 2 O 3 . The dielectric strength E d of suspension-sprayed coatings was found to be 19.5-26.8 kVAEmm 21 for coating thicknesses ranging from 60 to 200 lm. These values were slightly lower than those obtained for conventional HVOF coatings (up to 32 kVAEmm 21 ). However, it seemed that the dielectric strength of conventionally sprayed coatings was more sensitive to the coating thickness (when compared with the values of E d determined for S-HVOF coatings) and varied to a greater extent (up to 10 kVAEmm 21) when the coating thickness varied in the range 100-200 lm.
SOFC modules with a power of 5 to 50 kW are a serious competitor to commercially available combined heat and power plants for decentralized electricity and heat supply with high electrical efficiency. Electrical efficiency and electrical power of a SOFC stack are essential for its profitable operation. The highest power density and electrical efficiency can only be achieved with planar SOFC stacks. Electrolyte supported cells with 10ScSZ electrolytes allow power densities of more than 500 mW/cm². On account of the thermomechanical properties of electrolyte, this potential can only be used in stacks with chromium based interconnects (CFY from Plansee SE). High power, robustness and long-term stability are essential for stationary SOFC systems. In order to fulfill these requirements, Fraunhofer IKTS in close collaboration with Plansee SE develops a new stack design with larger active area, simple cathode contacting, external cathode manifold and optimized interconnect layer. This paper will give an overview of the current SOFC stack development focused on power output, long-term stability, temperature cycling and reliability of SOFC stack assembling. Material Combination for SOFC Stacks with High EfficiencyPlanar Solid Oxide Fuel Cells (SOFC) are considered to be highly efficient power generators with low emission levels even for small power units (1-200 kW el ). The recently developed and up-scaled net-shape technology for powder metallurgical production of bipolar plates allows new options for application of electrolyte supported cells with area specific resistances (ASR) <0.3 Ωcm² and are a match to stacks with anode supported cells (1-4). The electrolyte supported cells have benefits in long-term stability and thermal cyclability which were previously tested and are important parameter for a robust SOFC-system.The development of SOFC stacks with interconnects made from powder metallurgical processed chromium-iron-yttria based alloy (CFY) and scandia stabilized zirconia electrolytes (10ScSZ) have a long history and have surpassed the line to mass production in recent years.The bipolar plates of the new stack design (MK35x) have dimensions of 130x150x3.2 mm³. Currently, it is the biggest CFY interconnect and has a good ratio of active area to ECS Transactions, 35 (1) 269-277 (2011) 10.1149/1.3570002 © The Electrochemical Society 269 ) unless CC License in place (see abstract). ecsdl.org/site/terms_use address. Redistribution subject to ECS terms of use (see 160.39.73.191 Downloaded on 2015-03-24 to IP
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.