A combinatorial assessment of composition‐microstructure‐magnetic property relationships in magnetic high entropy AlCoxCr1‐xFeNi alloy (0 ≤ x ≤ 1) system has been carried out using compositionally graded alloys fabricated via laser additive manufacturing. At one end, the AlCoFeNi composition (x = 1) consisted of equiaxed B2 grains, exhibiting very early stages of phase separation (only compositional partitioning) into Ni–Al rich and Fe–Co rich regions within grains of the B2 phase. At the other extreme, the AlCrFeNi composition (x = 0) exhibited grains with pronounced spinodal decomposition, resulting in a B2 + bcc microstructure with the degree of spinodal decomposition progressively increasing with Cr content in these AlCoxCr1–xFeNi alloys. While the saturation magnetization (Ms) monotonically increases six times from x = 0 to x = 1, the coercivity (Hc) variation is non‐monotonic, increasing seven times from x = 0 to x = 0.4, and subsequently decreasing fourteen times from x = 0.4 to x = 1.0. The magnetic phase transition temperature (Tc) for these alloys also increases monotonically with increasing Co content with a second phase transition exhibited in a certain range of compositions between x = 0.6 to x = 0.8. Such substantial changes in the magnetization behavior and properties of magnetic high entropy systems opens possibilities of tuning these alloys for specific soft or hard magnetic component applications.

No abstract

Low cost, earth abundant, rare earth free magnetocaloric nanoparticles have attracted an enormous amount of attention for green, energy efficient, active near room temperature thermal management. Hence, we investigated the magnetocaloric properties of transition metal based (Fe70Ni30)100−xCrx (x = 1, 3, 5, 6 and 7) nanoparticles. The influence of Cr additions on the Curie temperature (TC) was studied. Only 5% of Cr can reduce the TC from ~438 K to 258 K. These alloys exhibit broad entropy v/s temperature curves, which is useful to enhance relative cooling power (RCP). For a field change of 5 T, the RCP for (Fe70Ni30)99Cr1 nanoparticles was found to be 548 J-kg−1. Tunable TCin broad range, good RCP, low cost, high corrosion resistance and earth abundance make these nanoparticles suitable for low-grade waste heat recovery as well as near room temperature active cooling applications.

No abstract

Low cost magnetocaloric nanomaterials have attracted considerable attention for energy efficient applications. We report a very high relative cooling power (RCP) in a study of the magnetocaloric effect in quenched FeNiB nanoparticles. RCP increases from 89.8 to 640 J kg À1 for a field change of 1 and 5 T, respectively, these values are the largest for rare earth free iron based magnetocaloric nanomaterials. To investigate the magnetocaloric behavior around the Curie temperature (T C ), the critical behavior of these quenched nanoparticles was studied. Detailed analysis of the magnetic phase transition using the modified Arrott plot, Kouvel-Fisher method, and critical isotherm plots yields critical exponents of b ¼ 0.364, c ¼ 1.319, d ¼ 4.623, and a ¼ À0.055, which are close to the theoretical exponents obtained from the 3D-Heisenberg model. Our results indicate that these FeNiB nanoparticles are potential candidates for magnetocaloric fluid based heat pumps and low grade waste heat recovery. V

No abstract

No abstract

A matrix of variably processed Fe-30at%Ni was deposited with variations in laser travel speeds as well and laser powers. A complete shift in phase stability occurred as a function of varying laser travel speed. At slow travel speeds, the microstructure was dominated by a columnar fcc phase. Intermediate travel speeds yielded a mixed microstructure comprised of both the columnar fcc and a martensite-like bcc phase. At the fastest travel speed, the microstructure was dominated by the bcc phase. This shift in phase stability subsequently affected the magnetic properties, specifically saturation magnetization. Ni-Fe-Mo and Ni-Fe-V permalloys were deposited from an elemental blend of powders as well. Both systems exhibited featureless microstructures dominated by an fcc phase. Magnetic measurements yielded saturation magnetizations on par with conventionally processed permalloys, however coercivities were significantly larger; this difference is attributed to microstructural defects that occur during the additive manufacturing process. Finally, a compositionally graded AlCoxCr1-xFeNi (0.0