Background: The development of better cross linked acrylic resin teeth has solved the problems related to wearing and discoloration of acrylic teeth. The same cross linking at ridge lap region acts as a double edge sword as it weakens the bond between denture base and tooth.

Masticatory efficiency is always compromised in complete denture patients. The denture teeth with compromised occlusal anatomy and material further compound the inherent limitations of complete dentures. To compare the masticatory efficiency of patients with complete denture using acrylic and metal occlusal posterior teeth. Ten edentulous patients with well-formed ridges were selected. Complete dentures using acrylic and metal occlusal posterior teeth were fabricated. The masticatory efficiency was calculated using photo colorimeter. Complete dentures with 20° acrylic resin posterior teeth were fabricated for ten edentulous patients and masticatory efficiency was measured using raw beetroot as test food on a photocolorimeter after 10, 15, 20 strokes. The acrylic resin posterior teeth were replaced with metal occlusal posterior teeth on the same denture base. The masticatory efficiency was measured by the same method. The mean average percentage of masticatory efficiency with acrylic resin teeth and metal occlusal teeth were first calculated and statistical analysis was done using students unpaired t test. The average masticatory efficiency with acrylic teeth was 46.46% and metal occlusal teeth was 65.62, 't' = 5.38. The difference between the mean average masticatory performance percentage with acrylic teeth and metal occlusal teeth was significant at 1% i.e. P < 0.01. Within the limitation of this study the average percentage value of masticatory efficiency improves considerably when metal occlusal teeth replace normal acrylic teeth without any alteration in position or relation.

Dentists are considered masters in technical skills and should be able to provide quick solutions to problems that can best be solved through communicating patiently with patients. Effective communication coupled with good clinical skills can lead to apt treatment and satisfaction for both the patient and the dentist. This article intends to highlight the communication skills that can improve the prognosis of complete denture treatment.

It was found that all the denture cleansing materials used in the study were effective in removing tea and turmeric stains. Products containing sodium perborate along with trisodium phosphate had a comparatively greater stain removal capability than products containing sodium perborate along with sodium bicarbonate followed by products containing sodium hypochlorite followed by water (control).

Objectives: To evaluate the fracture resistance efficacy of FRC posts and photo core, zirconia post and Parapost in endodontically treated teeth. Materials and Method: Thirty recently extracted mandibular first premolar teeth were randomly grouped in to 3 different groups with 10 samples in each group: FRC posts and photo core, zirconia post and Parapost. Fracture resistance in each group was estimated and compared. Results: The fracture resistance was 428.2, 432.1 and 232.5 for group I, II and III. The difference was statistically significant. The mean fracture resistance between group I to Group III and II with III was statistically significant (0.01). The fracture resistance between Group I and II was not significant (P>0.65). Conclusion: Authors found that zirconia and FRC posts exhibited higher fracture resistance as compared to paraposts.

No abstract

No abstract

Introduction Poly(methyl methacrylate) is widely used as denture base material due its better physical properties, ease to fabricate, and repair. Despite being the material of choice for the denture fabrication, dentures made from poly(methyl methacrylate) may exhibit dimensional changes due to volumetric shrinkage. This further affects the retention of the denture. Various methods have been used to overcome this problem. One such method is the use of injection molding technique. So, a study was planned to evaluate the efficacy of dentures processed by injection molding technique in reducing the volumetric shrinkage. Objective To evaluate and compare the dimensional accuracy of poly(methyl methacrylate) resin processed by conventional and injection molding technique. Materials and Methods A total of 90 samples were made. Half of the samples (45) were fabricated by compression molding and half (45) by injection molding technique. Dimensional change was studied at three equidistant points in posterior region with the help of digitized travelling microscope. Statistical analysis was done using student’s t-test. Result Dimensional accuracy of injection molded poly(methyl methacrylate) resin was greater than that of compression molded poly(methyl methacrylate).