Актуальність теми дослідження. Одне з найважливіших і трудомістких завдань при підготовці методик випробувань полягає в розрахунках кількісних характеристик випробувань, автоматизація яких при масовому проведенні випробувань стає актуальним завданням. Постановка проблеми. Ефективність функціонування випробувальної організації визначається часовими та якісними характеристиками проведення випробувань, де під якістю випробування розуміється відповідність одержаних оцінок параметрам випробувальних зразків. Вірогідність оцінок досягається неухильним та правильним проведенням випробування відповідно до розробленої методики, у якій вказуються, зокрема кількісні характеристики випробування конкретного зразка. Аналіз останніх досліджень і публікацій. На сьогодні є багато фундаментальних праць з питань планування експериментів, обробки їх результатів та одержання оцінок заданої якості. Останнім часом чимало наукових робіт присвячено автоматизації процесів підготовки, проведення та обробки результатів випробувань. Виділення недосліджених частин загальної проблеми. Алгоритмізація та автоматизація процесів планування у випробувальній організації має на меті суттєве спрощення, прискорення та позбавлення помилок при розробці методик випробування озброєння та військової техніки. Постановка завдання. Для моделювання процесів функціонування випробувальної організації і знаходження оптимальних режимів структури та параметрів виробничого процесу пропонується використання аналітичної моделі теорії систем масового обслуговування. Одним зі структурних елементів моделі має бути модуль планування випробувань, для якого необхідно розробити та підготувати до алгоритмування математичний апарат визначення кількісних характеристик плану проведення випробувань для одержання точкових оцінок параметрів зразку заданої точності й надійності, а також втрати надійності точкової оцінки внаслідок змушеного зменшення кількості випробувань. Виклад основного матеріалу. Сформовано структурно-функціональну схему модуля розрахунків кількісних характеристик випробувань. Розглянуто теоретичне питання одержання точкових оцінок параметрів випробувального зразку заданої точності та надійності. Обчислені кількісні характеристики випробувань для стандартизованих значень точності та надійності. Розглянуто питання зниження надійності оцінок при вимушеному зменшенні кількості дослідів. Визначені кількісні характеристики серійності випробувань для забезпечення надійності оцінок. Висновки відповідно до статті. Застосування розглянутого математичного апарату визначення кількісних показників плану проведення випробувань для одержання точкових оцінок параметрів зразку заданої точності й надійності в системі планування та управління випробуваннями дозволить суттєво скоротити часові витрати на підготовку до випробування, а алгоритмізація та подальша автоматизація дасть змогу уникнути впливу людського чинника при підготовці методик випробування.
The article is devoted to the analysis of the expediency of establishing high quantitative indicators of the level’s unification of military products and the formation of a methodical approach to justifying the requirements for these indicators, taking into account the volume of production. The requirements for standardization and unification (StU) are put forward in order to ensure high quality of products by reducing the terms and costs of their design and production preparation, as well as reducing the costs of samples operation (repair). Compliance with standards in Ukraine is a voluntary procedure but the Ministry of Defense during the development of tactical and technical tasks for the implementation of work on the creation (modernization) of special products puts forward requirements for compliance with standards (on the basis of consensus with the developer or manufacturer), including to StU. Also, the achieved quantitative indicators of the level of unification are evaluated according to the stages of work performance and during tests. It is known that the cost of a unit’s production depends on the volume of its production: the more units of production (samples) are produced, the lower the cost’s unit of production, as the specific (per unit of production) cost of development, preparation of production and actual production of products decreases. The article considers cases when it is inappropriate to set high StU indicators and the proposed general methodical approach to justifying the values of StU indicators of military products, taking into account the volume of their production. The specification of methodological instructions requires further research taking into account the practice of development (production) work and testing of products by their types.
The national security and defense capability of the state is largely determined by the level of equipping the armed forces with modern weapons and military equipment. An important point in the rearmament of the army is the high-quality and timely testing of the latest military models, which, to a large extent, is ensured by successful and systematic planning and management of test activities. The automated test support information system is aimed at solving such problems. During the IDEF0 notation, functional modeling of the armaments and military equipment testing system was designed, which allowed to determine the system-wide characteristics of information flows, but did not allow obtaining models performance evaluation. Existing methods for estimating distributed structures, as a rule, are reduced to estimating the connectivity of graph models and do not take into account the features of the interface of the IDEF0 notation functions.The article considers the issue of evaluation of functional models at the pre-design stage. A method for estimating the functional connectivity of processes in the functional modeling of complex systems using graph-ical notation IDEF0 and using automated design tools is proposed. The estimation has clear logical limits and is sensitive to changes in the parameters of the evaluated model. Due to the different importance of connections provided by the graphical notation interface IDEF0, it is proposed to use a scale of importance of the type of connection, which reflects the assessment of the connectedness of functions of strong or weak types of connections, and, accordingly, the success and rationality of functional configuration models. Estimates of the functional model of the weapons and military equipment test system are obtained.The use of the proposed evaluation method will allow to compare the structures of functional models of complex systems at the stage of pre-design studies
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.