The effect of chain architecture on the morphological and tensile properties of series of multigraft copolymers, with regularly spaced tri-, tetra-, and hexafunctional junction points, was investigated using transmission electron microscopy (TEM), small-angle X-ray scattering (SAXS), and tensile testing. The materials were synthesized by coupling difunctional polyisoprene (PI) spacers and living polystyrene (PS) branches, made by anionic polymerization, with chlorosilanes of different functionalities. Since the coupling process is a step-growth polymerization, yielding polydisperse products, fractionation was utilized to separate each material into three fractions (high, middle, and low molecular weight), each of low polydispersity. All three fractions have the same chain architecture on a per junction point basis but differ in the number of junction point units per molecule. By applying the constituting block copolymer concept, the physical behavior of these molecules was compared with current theories. It was found that morphological behavior of these graft copolymers can be predicted using theoretical approaches and is independent on the number of junction points. The number of the junction points, however, greatly influences the long-range order of microphase separation. Additionally, two new parameters for adjusting mechanical properties of multigraft copolymers were found in this investigation: (1) functionality of the graft copolymerstri-, tetra-, or hexafunctionalsand (2) number of junction points per molecule. An increase in functionality causes a change in morphology, resulting in a high level of tensile strength for tetrafunctional (cylindrical) and hexafunctional (lamellae) multigraft copolymers, leading to about the twice the strength of the spherical trifunctional multigrafts of similar overall composition. Tetrafunctional multigraft copolymers show a surprisingly high strain at break, far exceeding that of commercial block copolymer thermoplastic elastomers (TPEs). Strain at break and tensile strength increase linearly with the number of junction points per molecule. Hysteresis experiments at about 300-900% deformation demonstrate that multifunctional multigraft copolymers have improved high elasticity as compared to commercial TPEs like Kraton or Styroflex.

Summary: PS-PI multigraft copolymers with tri-tetra-and hexafunctional polystyrene branch points have been studied to investigate the influence of molecular architecture on morphological and tensile properties and to find novel material concepts. It was found that the morphological behaviour of these grafted copolymers can be predicted using theoretical approaches. The number of branch points, however, greatly influences the long-range order of microphase separation. Additionally, two new parameters for adjusting mechanical properties of multigraft copolymers are found in our investigations: 1) functionality of the graft copolymer: tri-, tetra-or hexafunctional and 2) number of branch points per molecule. Tetrafunctional multigraft copolymers show surprising high strain at break values up to 1550 %. With increasing number of branch points strain at break and tensile strength increase, where a linear dependence of mechanical properties on the number of branch points is obvious. Excellent elasticity of tetra and hexafunctional multigraft copolymers at high deformation was proved in hysteresis experiments.

The phenomenon of contact angle hysteresis was studied on smooth films of polyimide, a polymer type used in the microelectronic industry, by dynamic cycling contact angle measurements based on axisymmetric drop shape analysis-profile in combination with variable angle spectroscopic ellipsometry (VASE). It was found that both advancing and receding contact angles became smaller with increasing the number of cycles and are, therefore, not a property of the dry solid alone. The changes of the wetting behavior during these dynamic cycling contact angle measurements are attributed mainly to swelling and/or liquid retention. To reveal the water-induced changes of the polymer film, the polyimide surface was studied before and after the contact with a water droplet by VASE. Both the experimental ellipsometric spectrum for Delta and that for Psi as well as the corresponding simulations show characteristic shifts due to the contact with water. The so-called effective medium approximation was applied to recover information about the thickness and effective optical constants of the polymer layer from the ellipsometrically measured values of Delta and Psi. On the basis of these results, the swelling and retention behavior of the polyimide films in contact with water droplets were discussed.

No abstract

The influence of middle and outer block composition of symmetric triblock copolymers consisting of a polystyrene-polybutadiene (S/B) random middle block and two polystyrene (PS) outer blocks on morphology and rheological behavior has been investigated. Master curves are obtained by shifting the experimental data measured at different temperatures using time-temperature superposition principle, the validity of which was confirmed in the linear viscoelastic regime. The rheological properties are observed to be strongly influenced by the relative composition of the S-SB-S triblock copolymers. Increasing the S/B ratio from 1:1 to 1:2 in the middle block has lead to a change in morphology from wormlike to lamellar, which is also accompanied with broad and sharp tan d peaks in the dynamic mechanical measurements, respectively. The storage and loss modulus have been observed to increase with the increase in PS contents in the outer blocks and PB content in the middle block. The triblock copolymer with wormlike structure showed terminal linear viscoelastic behavior, whereas the ones with lamellar morphology showed nonterminal flow behavior in the similar low-frequency regime. The relaxation modulus (G t ) has been observed to increase four times when the S/B ratio is increased from 1:1 to 1:2, whereas it increases threefold when the PS-content in the outer block was increased by just 8 wt %.

The rheology and dynamic mechanical properties of binary block copolymer blends consisting of a symmetrical triblock copolymer with thermoplastic elastomeric behavior (LN4) and an asymmetrical thermoplastic triblock copolymer (LN3) were investigated. TEM images of the blends show a systematic variation in the morphologies from worms (∼20–0 wt % LN3) to cylinders (∼60–30 wt % LN3) to lamellae (100–70 wt % LN3) as a function of LN3 content. DMA analysis has revealed that the increase in LN3 content leads to a decrease in miscibility between the PS end blocks and the S/B middle block. The frequency and temperature dependence of the storage modulus (G′), loss modulus (G″), and complex viscosity (|η*|) has been studied for LN4 (weakly segregated) and LN3 (strongly segregated) from their master curves. By comparing the rheological properties of these blend compositions at low‐frequency regime, it is observed that with the increase in LN3 content the shear modulus and complex viscosity increase. Blend compositions with 70–100 wt % of LN3 show nonterminal behavior at reduced frequencies due to the presence of highly ordered microdomains when compared to blends with ∼0–20 wt % of LN3 content. van Gurp–Palmen plots were constructed to observe the transition from liquid‐ to solid‐like behavior in the vicinity of order‐to‐disorder transition (ODT) temperature. ODT temperature increases as the thermoplastic LN3 content increases which are also confirmed by the Han plots. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 329–343, 2008

No abstract

Summary Structure property correlations in a styrene‐butadiene star block copolymer melt mixed with varying amounts of multiwalled carbon nanotubes (MWCNTs) were evaluated. The MWCNTs are well dispersed within the matrix and do not significantly impact the star block copolymer morphology or the glass transition temperature. The electrical percolation threshold was found to be at ∼1 wt% of MWCNT concentration. A distinct increase in Young's modulus could be observed at a nanofiller content of 0.1 wt% while maintaining the elastomeric matrix property profile, an observation in tune with the rule‐of‐mixture prediction. Additionally the existence of double yielding was detected in these nanocomposites with a pronounced first yield point indicating a significant enhancement of stiffness in composites with low MWCNT content. Analysis of elastic moduli using Halpin‐Tsai and two‐phase Takayanagi model revealed a matrix‐controlled elastic response without any interfacial contribution due to MWCNT incorporation.