No abstract

For the vulcanized natural rubber (NR), incorporation of silver nanoparticles (AgNPs) into the NR matrix did not exhibit the bactericidal property against Escherichia coli (E. coli). However, incorporation of AgNPs into polyethylene (PE) matrix showed good antibacterial activities to both Gram-negative and Gram-positive bacteria. In the present work, NR/PE (85/15) blends have been prepared by melt blending with presence of compatibilizer in an internal mixer. To possess antibacterial property, AgNPs (5–10 nm) or Fe3O4–Ag hybrid nanoparticles (FAgNPs, 8 nm/16 nm) were added into PE matrix before its blending with NR component. The tensile test indicated that the presence of compatibilizer in NR/PE blend significantly enhanced the tensile strength and elongation at break (up to 35% and 38% increases, resp.). The antibacterial activity test was performed by monitoring of the bacterial lag-log growth phases with the presence of nanocomposites in the E. coli cell culture reactor. The antibacterial test showed that the presence of FAgNPs in NR/PE blend had a better antibacterial activity than that obtained with the lone AgNPs. Two similar reasons were proposed: (i) the faster Ag+ release rate from the Fe3O4–Ag hybrid nanoparticles due to the electron transfer from AgNP to Fe3O4 nanoparticle and (ii) the fact that the ionization of AgNPs in hybrid nanostructure might be accelerated by Fe3+ ions.

No abstract

Epoxy reinforced with two kinds of nanoparticles dealing with nano-SiO2 and nano-Fe2O3 was coated on steel rebar embedded in a chloride contaminated cement mortar. NaCl was added to the fresh Portland cement paste (at 0.3% and 0.5% by weight of cement) to simulate the chloride contamination at the critical level. The effect of incorporating nanoparticles on the corrosion resistance of epoxy-coated steel rebar was investigated by linear potentiodynamic polarization and electrochemical impedance spectroscopy. For the 0.3 wt.% chloride mortars, the electrochemical monitoring of the coated steel rebars during immersion for 56 days in 0.1 M NaOH solutions suggested the beneficial role of nano-Fe2O3 particles in significantly improving the corrosion resistance of the epoxy-coated rebar. After 56 days of immersion, the nano-Fe2O3 reduced the corrosion current of epoxy-coated rebar by a factor of 7.9. When the chloride concentration in the cement mortar was 0.5 wt.%, the incorporation of nanoparticles into the epoxy matrix did not enhance the corrosion resistance of epoxy coating for the rebar. At this critical level, chloride ions initiated rebar corrosion through nanoparticles at the epoxy/rebar interface.

The effect of incorporating nanoparticles on the corrosion resistance of epoxy-coated steel in salt contaminated mortars was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. Researchers conducted electrochemical monitoring of the coated steel embedded in mortar over 100 days of immersion in 0.1 M NaOH solutions. The chloride permeability and microstructure of Portland cement mortar with admixed nano-materials (at 1% by weight of cement) were examined using an electromigration test and field emission scanning electron microscopy (FESEM). Electrochemical monitoring showed that nano Fe₂O₃ improved the corrosion resistance of the coated rebar. The incorporation of a small amount of nano Fe₂O₃ (1% by total weight of resin and hardener) into the epoxy coating reduced the corrosion current of the epoxy-coated steel in chloride-contaminated mortar (0.3% chloride by weight of cement). After 100 days of immersion, the nanoparticles reduced the corrosion current of epoxy-coated steel by a factor of 6. The FESEM test revealed that admixing of nano-materials not only led to denser cement mortar but also changed the morphology of cement hydration products. The test results of compressive strength showed that nanoparticles increased the strength of cement mortar. The electromigration test showed that the incorporation of nanoparticles improved the chloride penetration resistance of the mortar, as indicated by the reduced apparent diffusion coefficients of the chloride anion. When nano-SiO₂ and nano-Fe₂O₃ were admixed into fresh cement mortar at 1% by weight of cement, the value of D(Cl−) was decreased by 83%, from 7.35×10(−11) m²/s (control specimen) to 1.21×10(−11) m²/s and 1.36×10(−11) m²/s, respectively.

Antibacterial polyethylene (PE)/silver nanoparticle (AgNP) nanocomposites containing AgNPs at concentrations of 5 × 10−5, 5 × 10−4, and 5 × 10−3 wt % were fabricated and tested. Transmission electron microscopy revealed an even dispersion of surface AgNPs in the PE/AgNP nanocomposites. No AgNP agglomeration was observed. The tensile strength, elongation at break, and Young's modulus of these PE/AgNP nanocomposites were similar to those of neat PE. Differential scanning calorimetry demonstrated that the PE/AgNP nanocomposites and neat PE had similar melting and crystallization temperatures of 126 ± 0.5 and 109 ± 0.6°C, respectively. The heats of fusion of the PE/AgNP nanocomposites containing AgNPs at concentrations of 5 × 10−5 and 5 × 10−4 and of 5 × 10−3 wt % were lower than those of neat PE by 5 and 7%, respectively. These PE/AgNP nanocomposites were immersed in shaking liquid cultures of the potential pathogenic bacteria Escherichia coli, Bacillus subtilis, and Salmonella typhimurium in the lag phase. The results show that the growth rates of all of the tested bacteria were restricted effectively after 1.5, 3, and 6 h of cultivation, respectively. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43331.

Ethylene propylene diene monomer (EPDM) is broadly employed as an insulating material for high voltage applications. Surface discharge-induced thermal depolymerization and carbon tracking adversely affect its performance. This work reports the electrical field modeling, carbon tracking lifetime, infrared thermal distribution, and leakage current development on EPDM-based insulation with the addition of nano-BN (boron nitride) contents. Melt mixing and compression molding techniques were used for the fabrication of nanocomposites. An electrical tracking resistance test was carried out as per IEC-60587. Simulation results show that contamination significantly distorted the electrical field distribution and induced dry band arcing. Experimental results indicate that electric field stress was noticed significantly higher at the intersection of insulation and edges of the area of contamination. Moreover, the field substantially intensified with the increasing voltage levels. Experimental results show improved carbonized tracking lifetime with the addition of nano-BN contents. Furthermore, surface temperature was reduced in the critical contamination flow path. The third harmonic component in the leakage current declined with the increase of the nano-BN contents. It is concluded that addition of nano-BN imparts a better tracking failure time, and this is attributed to better thermal conductivity and thermal stability, as well as an improved shielding effect to electrical discharges on the surface of nanocomposite insulators.

No abstract