Bóng che một phần là một hiện tượng phổ biến làm thay đổi hiệu suất của các hệ thống PV (Photovoltaic). Chúng có thể kể đến như: đám mây, bóng cây, cao ốc…và các điều kiện vận hành phức tạp. Bài viết này với mục tiêu so sánh hiệu suất phát điện của các cấu hình liên kết khác nhau như mắc nốitiếp (SC), mắc song song (PC) hay mắc hỗn hợp (SPC) dưới ảnh hưởng của hiện tượng bóng che một phần. Các cấu hình được đề xuất bao gồm sáu mô đun PV loại 72 tế bào công suất 200W được sử dụng để mô phỏng thông qua phần mềm PSIM. Việc nghiên cứu tập trung vào sự thay đổi đặc tính làm việc của các hệ thống khi thay đổi các yếu tố như: phạm vi bóng che, vị trí bóng che. Các kết quả thu được thông qua mô phỏng đã cho thấy những ảnh hưởng khác nhau đối với các cấu hình khác nhau trong cùng điều kiện vận hành. Nó được giải thích một cách chính xác rằng PC luôn đạt được công suất phát lớn nhất với số điểm phát công suất cực đại ít nhất. mặc dù điện áp ngõ ra của dạng cấu hình này không cao, cái mà có thể gây khó khăn cho việc thiết kế các bộ chuyển đổi DC-DC nhưng lại cho thấy sự ổn định nhất. Điều này có thể được ứng dụng rộng rãi trong việc chọn lựa kiểu cấu hình liên kết sao cho phù hợp với các yêu cầu đặt ra trong các nghiên cứu sau này để đạt được hiệu quả lớn nhất
An analysis is carried out for solidification around a cold cylinder in a rectangular cavity using numerical simulations. The transient influences of solidification accompanied by natural convection are investigated in detail. The governing equations, in terms of one-fluid formulation, including the Navier-Stokes and energy equations for incompressible Newtonian fluids are written for the whole domain. The no-slip and Dirichlet-type isothermal temperature boundary conditions are both implemented using a linear interpolation technique (immersed boundary method). The solidification interface is represented by connected elements that move on the fixed background grid. Code validations are carried out through various problems. Finally, the temporal dependence of the solid area ratio of the solid phase to the cylinder upon various dimensionless parameters, such as Rayleigh number, Prandtl number, Stefan number, thermal property ratios as well as a parameter indicating the effect of superheat is studied.
The paper presents the results of investigating the influence of Cu concentration on structure, mechanical properties and corrosion resistance of Ti 50 Ni 50¹x Cu x (x = 0, 5, 10, 15 and 20) alloy ribbons. The ribbons with a thickness of about 25 µm were prepared by using meltspinning method with a tangential velocity of copper wheel of 40 m.s ¹1 . All the ribbons reveal a single crystalline phase of (Ni,Cu)Ti with the martensitic-B19 structure at room temperature when Cu substitutes for Ni. The structural transformations temperature, tensile strain and elastic modulus increase with increasing Cu concentration whereas the hardness and dislocation density trendly decrease. The corrosion potential E corr in 3.5% NaCl aqueous solution increases from ¹0.67 V (for x = 0) to ¹0.46 V (for x = 20) indicating the better resistance against electrochemical corrosion by Cu addition.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.